Re:ADDING COOLANT AFTER RADIATOR REPLACEMENT
Thread Starter
Lead Lap
Joined: May 2006
Posts: 3,682
Likes: 304
Re:ADDING COOLANT AFTER RADIATOR REPLACEMENT
I have (as seen on recent threads) just had my radiator and thermostat replaced with a Denso aftermarket radiator and flushed and refilled with Red coolant that requires the addition of distilled water. Upon returning from Lexus and examining the job, I topped up the reservoir with approximately a half a cup (6 ounces?) of the red coolant/distilled water mixture. The reading when warm was at the full mark. I expected the next morning when the car was cold, for the level to drop back somewhat, which it did ever so slightly. I drove around most of the day and when I checked the level when the car was warm, it was lower than it was in the morning when cold. There were no visible signs of any external leaks. The temperature gauge is exactly where it was before the replacement (below the center and slightly above the 2nd line). Question.... when a radiator and thermostat are changed, as well as the old coolant flushed out and refilled, does it ever require a few top ups to get the coolant to it's proper level? I'm not sure if there may still be any air pockets that still need to purge or am I missing anything? Is there anything else I need to check? Any feedback would be greatly appreciated.
Last edited by Bocatrip; Sep 20, 2015 at 01:05 PM.
Thread Starter
Lead Lap
Joined: May 2006
Posts: 3,682
Likes: 304
It funny how I was thinking the exact same thing with regards to the heater core. It's been blazing hot here in Florida this past week and I wonder if the tech doing the work even bothered to put the heat on while replenishing the system. I haven't put the heat on since the install. I will check the system tomorrow when cold while removing the radiator cap when cold as well to see that the radiator is full. I'll keep the heater on for awhile and check again later. If any air pockets exist either in the heater core or elsewhere, do they dissipate on their own while topping up or must they be bled? I am not familiar with the heater water valve and am not planning on playing with it myself...
Last edited by Bocatrip; Sep 20, 2015 at 02:54 PM.
Trending Topics
Pole Position
Joined: Mar 2008
Posts: 2,146
Likes: 70
From: Illinois
Air in the system dissipates by bubbling up to the top of the radiator. The overflow container also supplies coolant in the event the radiator is low, but since you changed out the radiator, I would continue to check the level directly at the radiator cap after running for awhile and, of course, after the system has cooled sufficiently, even over night as you intend to do.
ClubLexus Stories
Celebrating Lexus & Toyota from Around the Globe
8 Tips for Improving Your Hybrid or Plug-in Hybrid's Efficiency!
Michael S. Palmer
10 Best Lexus Models No One Remembers
Joe Kucinski
TRD Off-Road Premium: Best 2026 4Runner, Except This One Thing
Michael S. Palmer
Top 10 Lexus & Toyotas to Drive Before You Die!
Joe Kucinski
Top 10 Lexus/Toyotas With The LEAST 5-Year Depreciation
Joe Kucinski
Lexus LC500 Convertible Auction: A Preview of Rising Values?
Brett Foote
GX 550 vs TX 550: Best 3-Row Luxury Lexus Family Hauler
Michael S. Palmer
9 Best Lexus Models You Can Buy for Half Price (And 1 You Shouldn't!)
Joe Kucinski
2026 Lexus NX Buyer's Guide: Models, Features, Prices & More!
Brett Foote
Thread Starter
Lead Lap
Joined: May 2006
Posts: 3,682
Likes: 304
Thank you RKW and Tom for your tremendous wealth of information. I guess what I'm getting at is this. Even if the tech was semi incompetent and did not remove the engine plugs while draining or even bleed from the heater water valve, will I still be able to get all air pockets out of the system by checking daily and adding any additional coolant that is necessary? If so, I'm fine with that. Of course, my car was originally filled by Lexus with the Pink coolant of which I requested to be removed and hopefully, they got most of it out before filling with the Toyota long life red. I guess, if you want the proper job done, you need to do it yourself, which in this case while living in Florida just isn't going to happen. Right now, I just want to get my coolant level where it should be...
Pole Position
Joined: Mar 2011
Posts: 2,187
Likes: 729
From: Texas
Boca, you will not have to mess with the heater water valve directly, just set the temperature setting to as high as it will go. The A/C ECU will open the heater water valve to supply heat. The repair manual suggests for you to rev the engine up to 2500 rpm to circulate the coolant.
Pole Position
Joined: Mar 2008
Posts: 2,146
Likes: 70
From: Illinois
And yes, all of the air will bubble up. Just check daily in the morning for a couple / few days. Opening the heater control valve (by turning temp control in the vehicle) all the way to high will allow for complete circulation of coolant which will push the air to the high end of the radiator.
Thread Starter
Lead Lap
Joined: May 2006
Posts: 3,682
Likes: 304
Boca, you will not have to mess with the heater water valve directly, just set the temperature setting to as high as it will go. The A/C ECU will open the heater water valve to supply heat. The repair manual suggests for you to rev the engine up to 2500 rpm to circulate the coolant.
Pole Position
Joined: Mar 2011
Posts: 2,187
Likes: 729
From: Texas
If I were you, I'd let the engine come up to temperature before switching the heat on. That way if the A/C is blowing hot air, I can tell the heater water valve is open. I'd keep the engine rev'ed up for 3-5 minutes top.
Thread Starter
Lead Lap
Joined: May 2006
Posts: 3,682
Likes: 304
My A/C always comes out cold from the vents within seconds of turning on the car even now.
Pole Position
Joined: Mar 2011
Posts: 2,187
Likes: 729
From: Texas
To open the heater water valve, you will have to turn up the temperature. Be sure to set it to the highest setting so that valve is fully open and sends hot coolant into the heater core (A/C will blow hot air).