ClubLexus - Lexus Forum Discussion
0 2022/01/15 20:03:04
It comes with the usb to car cable and the software disc.
It comes with the usb to car cable and the software disc.
0 2022/01/07 17:47:41
They were past their prime.
They were past their prime.
0 2022/01/07 13:43:11
I used a mirror to verify they were fully installed. They are easy to reach and replace from under the car but difficult to see from the top without a mirror.
I used a mirror to verify they were fully installed. They are easy to reach and replace from under the car but difficult to see from the top without a mirror.
0 2022/01/07 13:43:05
3 new bushings
3 new bushings
0 2022/01/07 13:42:40
Under $10 :)
Under $10 :)
0 2022/01/07 13:42:33
0 2022/01/04 21:24:17
On the 600 the rack mounts to the front of the subframe, easy access.
On the 600 the rack mounts to the front of the subframe, easy access.
0 2022/01/04 21:21:06
close up of my 600 rear bushing. By looking at it I do get the feeling the bushing is glued or melted in.
close up of my 600 rear bushing. By looking at it I do get the feeling the bushing is glued or melted in.
0 2021/12/21 08:55:07
0 2021/12/21 08:51:29
close up of my 600 rear bushing
close up of my 600 rear bushing
0 2021/12/21 08:30:48
It doesn't appear to be shaped like the oem bushing. I wrote LS460 rear sway on the box 4 years ago. I don't see them offered on febests site.
It doesn't appear to be shaped like the oem bushing. I wrote LS460 rear sway on the box 4 years ago. I don't see them offered on febests site.
0 2021/12/21 08:30:33
It's filled with more rubber than the one I removed.
It's filled with more rubber than the one I removed.
0 2021/12/20 19:04:40
This bushing was easy to replace.
This bushing was easy to replace.
0 2021/12/20 19:04:28
My other 3 rims look like trash :)
My other 3 rims look like trash :)
0 2021/12/20 19:01:01
The shock and sway bar link are difficult to install at the same time. I discovered if you install one then try to install the other it won't slide in lol. I installed the shock, sway bar link, main bolt, then jacked it up to bolt the main ball joint to the knuckle.
The shock and sway bar link are difficult to install at the same time. I discovered if you install one then try to install the other it won't slide in lol. I installed the shock, sway bar link, main bolt, then jacked it up to bolt the main ball joint to the knuckle.
0 2021/12/20 18:45:01
The new bushing pushed into the arm easily. Getting the arm reinstalled into the car is easier than it looks.
The new bushing pushed into the arm easily. Getting the arm reinstalled into the car is easier than it looks.
0 2021/12/20 18:44:09
Getting the lower rear arms lined up into the knuckle / ball joint proved to be tricky. I couldn't get enough leverage by hand to line them up. The new bushings were tight! ( picture of the left front looking forward)
Getting the lower rear arms lined up into the knuckle / ball joint proved to be tricky. I couldn't get enough leverage by hand to line them up. The new bushings were tight! ( picture of the left front looking forward)
0 2021/12/20 18:24:25
The ratchet strap worked great. It pulled the knuckle into place and the arm fell right in. ( right front )
The ratchet strap worked great. It pulled the knuckle into place and the arm fell right in. ( right front )
0 2021/12/20 18:24:07
On both sides I used a ratchet strap as a helping hand. ( right side of car looking forward )
On both sides I used a ratchet strap as a helping hand. ( right side of car looking forward )
0 2021/12/20 18:23:55
It's filled with a lot more rubber than the one I removed.
It's filled with a lot more rubber than the one I removed.
0 2021/12/20 18:21:48
The new bushing pressed in without any issues.
The new bushing pressed in without any issues.
0 2021/12/20 18:21:32
I left the ball joint attached to make life easier.
I left the ball joint attached to make life easier.
0 2021/12/20 18:18:19
The metal block is holding the section of arm where I removed the small piece of bushing.
The metal block is holding the section of arm where I removed the small piece of bushing.
0 2021/12/20 18:18:06
Bushing is out!
Bushing is out!
0 2021/12/20 18:16:51
With that small section of bushing removed I was able to support the arm on my press to remove the bushing.
With that small section of bushing removed I was able to support the arm on my press to remove the bushing.
0 2021/12/20 18:11:37
I used a cutoff saw to cut part of the bushing off. Another section of the bushing rests right on the control arm. I cut through it most of the way with the cutoff saw then finished removing the chunk with a screw driver and hammer.
I used a cutoff saw to cut part of the bushing off. Another section of the bushing rests right on the control arm. I cut through it most of the way with the cutoff saw then finished removing the chunk with a screw driver and hammer.
0 2021/12/20 18:11:27
There is no easy way to press this bushing out.
There is no easy way to press this bushing out.
0 2021/12/20 18:09:47
Top is awd bushing from my above post. Lower is rwd bushing.
Top is awd bushing from my above post. Lower is rwd bushing.
0 2021/12/04 11:32:22
0 2021/12/04 10:53:39
The lower bushing is from a 460 rwd.
The lower bushing is from a 460 rwd.
0 2021/12/04 10:49:11
I'm tempted to fill this area for a bit more rigidity.
I'm tempted to fill this area for a bit more rigidity.
0 2021/12/04 10:47:43
7k miles
7k miles
0 2021/11/29 19:29:17
4 years old 15-20k ish miles
4 years old 15-20k ish miles
0 2021/11/29 19:29:09
4 years old 15-20k ish miles
4 years old 15-20k ish miles
0 2021/11/29 19:29:00
Same part just different angle.
Same part just different angle.
0 2021/11/22 16:07:18
The struggle is real. This is the new oem right lower forward control arm I put in 7000 miles ago. The bushing is already tearing.
The struggle is real. This is the new oem right lower forward control arm I put in 7000 miles ago. The bushing is already tearing.
0 2021/11/22 16:07:12
0 2021/11/22 16:07:04
0 2021/11/22 16:07:00
0 2021/11/22 16:06:55