Scottish Aristo. Large single, six speed, Wide arch
#1
Driver School Candidate
Thread Starter
Join Date: Dec 2016
Location: scotland
Posts: 13
Likes: 0
Received 0 Likes
on
0 Posts
Scottish Aristo. Large single, six speed, Wide arch
Hey guys. Had the car since 2009. Long term love affair with the car thats seen me get familiar with every single nut and bolt on the car.
Started in 2009 with a almost stock low mileage car that'd only been in the UK for 2 years. Car was immaculate !! came with 5zigen lowering springs. Fujitsubo exhaust, HKS mushroom intake and 19" BBS LM's
Dyno figures indicated 330bhp at that point
Started in 2009 with a almost stock low mileage car that'd only been in the UK for 2 years. Car was immaculate !! came with 5zigen lowering springs. Fujitsubo exhaust, HKS mushroom intake and 19" BBS LM's
Dyno figures indicated 330bhp at that point
Last edited by kwalker705; 09-16-17 at 05:51 PM.
#2
Driver School Candidate
Thread Starter
Join Date: Dec 2016
Location: scotland
Posts: 13
Likes: 0
Received 0 Likes
on
0 Posts
2009 - 2010 I started making some small upgrades to the car.
Changed the suspension springs to HSD coilovers, Removed the cat, turned the boost up to 1.2bar and the car made 401bhp on the dyno
Took the car to an old airfield used for 1/4 mile racing from time to time. Not any startling times but managed to shock a few unsuspecting racers with how quick the aristo is.
Changed the suspension springs to HSD coilovers, Removed the cat, turned the boost up to 1.2bar and the car made 401bhp on the dyno
Took the car to an old airfield used for 1/4 mile racing from time to time. Not any startling times but managed to shock a few unsuspecting racers with how quick the aristo is.
#3
Driver School Candidate
Thread Starter
Join Date: Dec 2016
Location: scotland
Posts: 13
Likes: 0
Received 0 Likes
on
0 Posts
2011 things started getting a bit more serious.
Fitted Ksport 365mm front discs and 6 pot calipers. TOMS rear subframe braces were fitted and I for some unknown reason decided I was gonna buy a large Holset HX35 turbo and manifold.
Had the whole lot fitted up by late 2011 and got the car up and running.
Mapper was all booked up to set the car up using an AEM FIC. Unfortunately shortly before mapping another aristo using the FIC started to develop problems and the mapper decided he wouldn't use them anymore. Luckily for me the mapper is also the creator and owner of Syvecs. He suggested using the syvecs. That created a problem though. Back then syvecs wasn't capable of being used with the aristo's tiptronic transmission.
Fitted Ksport 365mm front discs and 6 pot calipers. TOMS rear subframe braces were fitted and I for some unknown reason decided I was gonna buy a large Holset HX35 turbo and manifold.
Had the whole lot fitted up by late 2011 and got the car up and running.
Mapper was all booked up to set the car up using an AEM FIC. Unfortunately shortly before mapping another aristo using the FIC started to develop problems and the mapper decided he wouldn't use them anymore. Luckily for me the mapper is also the creator and owner of Syvecs. He suggested using the syvecs. That created a problem though. Back then syvecs wasn't capable of being used with the aristo's tiptronic transmission.
#4
Driver School Candidate
Thread Starter
Join Date: Dec 2016
Location: scotland
Posts: 13
Likes: 0
Received 0 Likes
on
0 Posts
So if syvecs couldnt be used with the tiptronic autobox there was only one solution....... a getrag 6 speed transmission swap
Due to work commitments and at the time my limited mechanical knowledge I contacted Paul at Sbody automotive about taking care of the box swap. He built his own nissan G35 falken drift car with a 2jz, 6 speed box, clamshell front and rear and 700+bhp. He was the ideal man for the job.
Due to work commitments and at the time my limited mechanical knowledge I contacted Paul at Sbody automotive about taking care of the box swap. He built his own nissan G35 falken drift car with a 2jz, 6 speed box, clamshell front and rear and 700+bhp. He was the ideal man for the job.
Last edited by kwalker705; 09-16-17 at 05:50 PM.
#5
Driver School Candidate
Thread Starter
Join Date: Dec 2016
Location: scotland
Posts: 13
Likes: 0
Received 0 Likes
on
0 Posts
The HX35 turbo was going to be used and limited to 450bhp to save blowing the standard autobox to pieces.
After getting the 6 speed installed there was no need to limit the power figures. So the decision was made to remove the holset unit and change out for a garage whifbitz kit. Went for a twin 40mm wastegate setup , 3" downpipe and a Borgwarner S366 turbo.
While the car was away having the box done I decided to have them fit the turbo kit, an HKS timing belt, a driftworks oil cooler and filter relocation kit. Sbody automotive also got together with syvecs and installed the ECU and took care of the mapping. Vibratechnics developed some engine mounts for the car aswell
Car came back with 567bhp and 560ft/lbs of torque and was a hell of a handfull.
Next on the list was a Kazz LSD. Hated the Kazz unit and ended up changing to a Tomei unit which was much smoother and refined.
After getting the 6 speed installed there was no need to limit the power figures. So the decision was made to remove the holset unit and change out for a garage whifbitz kit. Went for a twin 40mm wastegate setup , 3" downpipe and a Borgwarner S366 turbo.
While the car was away having the box done I decided to have them fit the turbo kit, an HKS timing belt, a driftworks oil cooler and filter relocation kit. Sbody automotive also got together with syvecs and installed the ECU and took care of the mapping. Vibratechnics developed some engine mounts for the car aswell
Car came back with 567bhp and 560ft/lbs of torque and was a hell of a handfull.
Next on the list was a Kazz LSD. Hated the Kazz unit and ended up changing to a Tomei unit which was much smoother and refined.
#6
Driver School Candidate
Thread Starter
Join Date: Dec 2016
Location: scotland
Posts: 13
Likes: 0
Received 0 Likes
on
0 Posts
while driving the car home after the mapping was complete i managed to obliterate a large fox with the front bumper. Unfortunately the bumper came off a little worse for wear with the splitter breaking into 3 parts.
Managed to fibreglass it back together and had the whole front bumper painted.
Sent the BBS LMs away for refinishing at that point too.
Then managed to get a small feature in speedhunters. shame they used my "have a look at this pics" from my camera phone for the article instead of asking for better pics with my DSLR
http://www.speedhunters.com/2012/06/567hp_arist/
Managed to fibreglass it back together and had the whole front bumper painted.
Sent the BBS LMs away for refinishing at that point too.
Then managed to get a small feature in speedhunters. shame they used my "have a look at this pics" from my camera phone for the article instead of asking for better pics with my DSLR
http://www.speedhunters.com/2012/06/567hp_arist/
#7
Driver School Candidate
Thread Starter
Join Date: Dec 2016
Location: scotland
Posts: 13
Likes: 0
Received 0 Likes
on
0 Posts
Spec at this stage was
2jzgte
whifbitz turbo manifold
2x 40mm turbosmart wastegates
BW S366 turbo
3" downpipe
2.5" fujitsubo exhaust
K&N filter
HKS timing belt
whifbitz pulley set
driftworks oil cooler kit
2x walbro 255lph fuel pumps on custom hanger
aeromotive FPR
3" front mount intercooler and custom pipework
ID 1000cc injectors
whifbitz twin feed fuel rail
innovate closed loop lambda/wideband
Syvecs S6 ECU . 567bhp 560ft/lbs torque.
HSD coilovers
TOMS subframe brace kit
summit racing front strut brace
Ksport 365mm front brake conversion, 6 pot calipers
19"BBS LMs
Tomei LSD
EBC yellow stuff rear brake pads
Plenty more info to come on this ongoing saga of a project
2jzgte
whifbitz turbo manifold
2x 40mm turbosmart wastegates
BW S366 turbo
3" downpipe
2.5" fujitsubo exhaust
K&N filter
HKS timing belt
whifbitz pulley set
driftworks oil cooler kit
2x walbro 255lph fuel pumps on custom hanger
aeromotive FPR
3" front mount intercooler and custom pipework
ID 1000cc injectors
whifbitz twin feed fuel rail
innovate closed loop lambda/wideband
Syvecs S6 ECU . 567bhp 560ft/lbs torque.
HSD coilovers
TOMS subframe brace kit
summit racing front strut brace
Ksport 365mm front brake conversion, 6 pot calipers
19"BBS LMs
Tomei LSD
EBC yellow stuff rear brake pads
Plenty more info to come on this ongoing saga of a project
Last edited by kwalker705; 09-16-17 at 06:19 PM.
Trending Topics
#10
Driver School Candidate
Thread Starter
Join Date: Dec 2016
Location: scotland
Posts: 13
Likes: 0
Received 0 Likes
on
0 Posts
#11
Thread
Thread Starter
Forum
Replies
Last Post
CAN-Toronto Fs 1993 LEXUS GS300 2JZGTE / Aristo $7800
CHASER4LIF
Lexus Vehicles Classifieds
5
01-24-13 05:40 PM
rcyo1
GS - 2nd Gen (1998-2005)
17
04-12-05 08:43 PM