ClubLexus - Lexus Forum Discussion
0 2016/01/07 19:30:04
0 2016/01/07 17:49:34
Tri-electrode NGK
Tri-electrode NGK
0 2016/01/07 17:48:33
Close up shot of original fuses.
Close up shot of original fuses.
0 2016/01/06 21:02:32
All original fuses.
All original fuses.
0 2016/01/06 21:01:41
New cushion
New cushion
0 2016/01/04 22:22:31
Front set of oil line cushions on passenger side above oil pan front corner
Front set of oil line cushions on passenger side above oil pan front corner
0 2016/01/04 22:18:43
Rear set of cushions just below passenger side exhaust manifold at connector for upstream oxygen sensor
Rear set of cushions just below passenger side exhaust manifold at connector for upstream oxygen sensor
0 2016/01/04 22:15:25
Parts 3296 are oil cooler line cushions.
Parts 3296 are oil cooler line cushions.
0 2016/01/04 22:13:02
Old oil cooler line cushions
Old oil cooler line cushions
0 2016/01/04 22:09:56
LS430 Connectors G1and G2
LS430 Connectors G1and G2
0 2016/01/02 20:29:21
LS400 Generator Connectors G1 and G2
LS400 Generator Connectors G1 and G2
0 2016/01/02 20:27:17
OEM Alternator connector for LS400 and LS430
OEM Alternator connector for LS400 and LS430
0 2016/01/02 20:24:10
After molten lead inserted into gas pedal...
After molten lead inserted into gas pedal...
0 2015/12/31 12:06:26
Image of original gas pedal backside...depicting lattice pockets
Image of original gas pedal backside...depicting lattice pockets
0 2015/12/31 11:56:24
0 2015/12/20 20:50:53
Main fuel line on 1999 LS400 asrtride and aside exhaust manifold heat shield. What were they thinking!? Room for improvement here.
Main fuel line on 1999 LS400 asrtride and aside exhaust manifold heat shield. What were they thinking!? Room for improvement here.
0 2015/12/19 21:05:36
0 2015/12/19 16:37:50
The image depicts positioning of the Inector wrap around the left front injector. Fitment was accomplished by using a long needle nose pliers (suggest you do not use one with side cutter to avoid inadvertently cutting or nicking wires) and a You notice all of the exposed wires..The heatshrink tubing on the entire engine harness has disintegrated. DJI offers Hi-temperature products designed for engine compartment wiring management ...heatshrink , pre-split and tape. Perhaps my next write-up.
The image depicts positioning of the Inector wrap around the left front injector. Fitment was accomplished by using a long needle nose pliers (suggest you do not use one with side cutter to avoid inadvertently cutting or nicking wires) and a You notice all of the exposed wires..The heatshrink tubing on the entire engine harness has disintegrated. DJI offers Hi-temperature products designed for engine compartment wiring management ...heatshrink , pre-split and tape. Perhaps my next write-up.
0 2015/12/19 15:51:50
The Injector wrap, both sides before fitment around the injectors.
The Injector wrap, both sides before fitment around the injectors.
0 2015/12/19 15:45:08
Here are the 8 Injector covers as received fron DEI. They consist of a durable reflective foil barrier(not shown) and a high temperature rated pliable glass fiber weave. Velcro type tabs on opposite opposing ends provide custom fit to each injector...On our cars all 8 injectors, wraps do not cover the same, so flexible fitment is imperative.
Here are the 8 Injector covers as received fron DEI. They consist of a durable reflective foil barrier(not shown) and a high temperature rated pliable glass fiber weave. Velcro type tabs on opposite opposing ends provide custom fit to each injector...On our cars all 8 injectors, wraps do not cover the same, so flexible fitment is imperative.
0 2015/12/19 15:29:24
Installion instructions are straightforward....but we advocate disconnecting the negative ground from our cars and not the positive cable...
Installion instructions are straightforward....but we advocate disconnecting the negative ground from our cars and not the positive cable...
0 2015/12/19 15:24:36
The black wire harness clamp is correct. Lexus is offering the incorrect part in brown.
The black wire harness clamp is correct. Lexus is offering the incorrect part in brown.
0 2015/12/12 10:49:21
Push-on bracket clamp showing 10 mm inner diameter marking.
Push-on bracket clamp showing 10 mm inner diameter marking.
0 2015/12/12 10:48:17
Remainder of wire loom engine harness plastic clamp on driver side at intake manifold.
Remainder of wire loom engine harness plastic clamp on driver side at intake manifold.
0 2015/12/12 10:47:38
Dismembered plastic hole insertion clamp showing lances.
Dismembered plastic hole insertion clamp showing lances.
0 2015/12/12 10:45:22
0 2015/12/11 18:40:22
Wiper motor mounting bushings are degraded and age hardened
Wiper motor mounting bushings are degraded and age hardened
0 2015/11/30 18:05:34
LS400 Exhaust System exhibiting design issues resolved in the LS430
LS400 Exhaust System exhibiting design issues resolved in the LS430
0 2015/11/28 19:29:51
LS430 Exhaust Diagram.fewer harsh transitions
LS430 Exhaust Diagram.fewer harsh transitions
0 2015/11/28 19:29:36
A Denso oxygen sensor
A Denso oxygen sensor
0 2015/11/28 19:23:23
This engineered extender is a bolt in for 1999 LS400 through earlier 1995-2000 LS400. I would not use inserts and would consider shortening housing to bring tip of post -cat oxygen sensor closer to perimeter of exhaust pipe - the goal is not to defeat it's purpos but relocate it from exhaust st ream
This engineered extender is a bolt in for 1999 LS400 through earlier 1995-2000 LS400. I would not use inserts and would consider shortening housing to bring tip of post -cat oxygen sensor closer to perimeter of exhaust pipe - the goal is not to defeat it's purpos but relocate it from exhaust st ream
0 2015/11/25 09:30:14
The Oxygen sensor probe is a major restriction...and its turbulence exacerbates this. While ordinarily the sensor should reside in the middle of the exhaust stream, this sensor does not influnce ECU air/fuel mixture but monitors randomly whether cats are performing.
The Oxygen sensor probe is a major restriction...and its turbulence exacerbates this. While ordinarily the sensor should reside in the middle of the exhaust stream, this sensor does not influnce ECU air/fuel mixture but monitors randomly whether cats are performing.
0 2015/11/25 09:29:54
The waterpump has some type of serialization on the hub...but whose?
The waterpump has some type of serialization on the hub...but whose?
0 2015/11/23 19:54:34
This Autozone acquired timing belt appears too thin and the casing abraded.
This Autozone acquired timing belt appears too thin and the casing abraded.
0 2015/11/23 19:47:50
Coolant dripping from where water pump resides. Dry at uptop coolant junctions, hoses and fittings...
Coolant dripping from where water pump resides. Dry at uptop coolant junctions, hoses and fittings...
0 2015/11/23 19:41:21
"New" timing belt tensioner pulley exhibiting significant corrossion for a non-original part... Is this typical?
"New" timing belt tensioner pulley exhibiting significant corrossion for a non-original part... Is this typical?
0 2015/11/23 19:39:29
Inside right cam timing belt cover caked with rubber dust
Inside right cam timing belt cover caked with rubber dust
0 2015/11/23 19:35:04
0 2015/11/23 18:55:52
0 2015/11/18 08:13:04