Official "MODDED" CT200h picture thread!
I'll post some pics of my car later when i get home from work
I'll post some pics of my car later when i get home from work
The diffuser definitely improves the look of the rear end, especially after I put on the exhaust. My exhaust didn't look right prior to putting on the diffuser.
I'll be looking forward to seeing what you got!

My current setup:
Megan Coilovers
Megan rear camber arms / cam bolts in front
Work CR2P (19"x9.5" +16 rears; 19"x9.5" +45 fronts; 215/35r/19 Kumho tires)
12" Alpine type R powered by a Pioneer GMD8601




My current setup:
Megan Coilovers
Megan rear camber arms / cam bolts in front
Work CR2P (19"x9.5" +16 rears; 19"x9.5" +45 fronts; 215/35r/19 Kumho tires)
12" Alpine type R powered by a Pioneer GMD8601
Attachment 407623
Attachment 407624
Attachment 407625
Attachment 407626
Attachment 407709
Attachment 407709
Celebrating Lexus & Toyota from Around the Globe
If I build one, it will be similar to this one:
http://www.ct200hforum.com/forum/lex...d-stealth.html
See, we are lucky because we have that useless foam piece over the spare tire that is just designed to raise the rear trunk height to match the battery pack height. I think we could actually use those hollow spaces to our advantage and have a sub on each side, and use the hollow space as a resonance chamber. Then you could drill a hole about 1.5"-2" in diameter in the carpet of the removable side panels, and a ton of base would blast out! You could probably find a chrome ring of the same diameter to make it look pro!
that is why, unlike the design above, I would put the amp in the middle, and have two 10" subs at an angle on each side. Then the resonance chambers I mentioned would work better. Then to top it all off, I would put a plexiglass window on the top at trunk height, line the wooden housing with carbon fiber vinyl, and add some blue LED's to illuminate the amp and subs... I think it would look amazing!
(Just make sure you add length to all the wires so you can remove the entire unit to get the spare tire and jack out... Ideally it could be designed with hinges or a lift mechanism but I think that is just getting too complicated!)
I feel like the moderator should think about making these posts about the sub another topic because I was just thinking it's OT.
Last edited by SteveMason; Apr 15, 2017 at 09:59 PM.

My current setup:
Megan Coilovers
Megan rear camber arms / cam bolts in front
Work CR2P (19"x9.5" +16 rears; 19"x9.5" +45 fronts; 215/35r/19 Kumho tires)
12" Alpine type R powered by a Pioneer GMD8601
Attachment 407623
Attachment 407624
Attachment 407625
Attachment 407626
I've been a long time lurker here, and now I thought I should probably show myself. I bought my '15 CT F-Sport two years ago new from the dealer, and during these two years I've done a couple of mods:
Injen Intake
HKS Exhaust
F-Sport Sway bars
BC BR Coilovers
AG M240 18" Wheels (Temporary until my Work VS-XXs come in)
Modellista Front Lip Spoiler & Side Skirts
TRD Rear Bumper Diffuser
I also have the StanceParts Front Air Cup Suspension Kit, but never had the chance to install it yet.
I've also added some little touches like the OEM sun visors, clean box, cup holder plates, and rear cupholders. All OEM.
https://www.clublexus.com/forums/ct-...ml#post9838538
https://www.clublexus.com/forums/is-...t-now-302.html






