keeps popping up
May 23, 2012 | 09:31 AM
Thread Starter
Joined: Oct 2010
Posts: 698
Likes: 0
From: New Jersey
keeps popping up
dose anybody know to stop the box on from keep coming up on the right side
Last edited by bacardi; May 23, 2012 at 09:35 AM .
May 23, 2012 | 02:07 PM
Joined: Dec 2009
Posts: 3,135
Likes: 276
From: CA - San Diego
Huh??????????
What box? I'm confused.
Last edited by VVTiBob; May 24, 2012 at 11:57 AM .
May 23, 2012 | 03:12 PM
Thread Starter
Joined: Oct 2010
Posts: 698
Likes: 0
From: New Jersey
May 23, 2012 | 04:44 PM
Joined: Mar 2012
Posts: 431
Likes: 0
From: PA
Remove the muffler bearings. Then it will stop.
May 24, 2012 | 08:02 AM
Joined: Jan 2007
Posts: 2,799
Likes: 45
From: NC
Probably just low on hood coolant.
May 24, 2012 | 08:57 AM
Joined: Feb 2007
Posts: 2,090
Likes: 10
From: NM
Quote:
Originally Posted by
bacardi
dose anybody know to stop the box on from keep coming up on the right side
I think your post is missing a word or two.
May 24, 2012 | 09:47 AM
Joined: Feb 2007
Posts: 1,637
Likes: 60
From: DC
This happened to me a couple of years ago. It turned out that the box dampener on the right side had gone bad and so there was nothing to keep it from coming up. The dealership wanted almost $5,000 to install a new dampener. I did it myself in about 10 minutes. Problem solved.
May 24, 2012 | 09:55 AM
Joined: Apr 2011
Posts: 89
Likes: 2
From: Cambridgeshire
Check the flange plate, because its probably gone out of skew on the treadle.
May 24, 2012 | 05:11 PM
Joined: Jul 2010
Posts: 365
Likes: 8
From: Quebec
Check the kick-down fluid in the reservoir... Level might be low!
May 24, 2012 | 06:12 PM
Joined: Mar 2012
Posts: 130
Likes: 1
From: CA
Radiator bearings, definately radiator bearings.
May 24, 2012 | 06:23 PM
Joined: Jan 2004
Posts: 450
Likes: 4
From: Florida
Quote:
Originally Posted by
sebtown
Radiator bearings, definately radiator bearings.
Not the carbeurator?
May 25, 2012 | 05:03 AM
Joined: Mar 2012
Posts: 431
Likes: 0
From: PA
Boy, you learn so much neat information on this site!!
May 25, 2012 | 05:44 AM
Joined: Apr 2012
Posts: 28
Likes: 0
From: New Jersey
Quote:
Originally Posted by
ser67
Check the flange plate, because its probably gone out of skew on the treadle.
Check the Finigan Pin then check the flow of the Dynoflow.
May 25, 2012 | 01:02 PM
Joined: Mar 2012
Posts: 130
Likes: 1
From: CA
May also mant to check for poper alignment of the Johnson Rod
May 25, 2012 | 01:09 PM
Joined: Dec 2009
Posts: 3,135
Likes: 276
From: CA - San Diego
I checked my "Johnson" and it is aligned properly.
sorry, just couldn't resist
What box? I'm confused. 
