When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.
40ft cord on an appliance that draws 15 amps? Ohms law does not approve.
Please elucidate why an appliance cord with 0.101 ohm of resistance is a problem. These things will very happily run on 122V received at the pump from a 125V outlet.
Originally Posted by Striker223
Likely "15 amp" like "5 hp" vacuums....
They do draw high 14.X Amps pretty consistently in several instrumented tests I've seen.
Please elucidate why an appliance cord with 0.101 ohm of resistance is a problem. These things will very happily run on 122V received at the pump from a 125V outlet.
They do draw high 14.X Amps pretty consistently in several instrumented tests I've seen.
Well that's an issue for me, I will have to install another circuit....again. I really question who decided a single 20 amp was enough for all the outlets in my garage.....I've already had to add another to run a compressor
Well that's an issue for me, I will have to install another circuit....again. I really question who decided a single 20 amp was enough for all the outlets in my garage.....I've already had to add another to run a compressor
Unless you have multiple high-current items actually running simultaneously, it shouldn't be an issue. So don't run the pressure washer AND your compressor AND a worm drive saw at the same time on the same circuit.
Please elucidate why an appliance cord with 0.101 ohm of resistance is a problem. These things will very happily run on 122V received at the pump from a 125V outlet.
You really think this cord will have pure copper 14 gauge wire? Most likely 75 watts will be dissipated by the power cord alone.
You really think this cord will have pure copper 14 gauge wire? Most likely 75 watts will be dissipated by the power cord alone.
edit - your resistance figure is 2x too low.
My resistance figure isn't 2x too low, I just forgot to account for both wires (hot and neutral) in the voltage drop calculation. So consider me half corrected on that count.
You actually made me go look at the cable spec. It's 2x16AWG 105C, which has a current capacity of 24A per wire with the insulation factored in. It has a resistance of 4.016 ohms per 1,000 feet, so 0.16064 for 40 feet.
Current x resistance x #conductors is 15 x 0.16064 x 2, or a voltage drop of 4.82V. So yes, ~72W dissipated. But still well within safe limits. 1,875W drawn from the wall, 1,800 delivered to the pump. For a couple of 1-3 minute cycles over the course of a 20-30 minute cleaning session, this is not a concern at all.
I think I'll get one too, seems powerful enough to run a foam cannon. Just want to make sure it's out of the way/hose can be managed well, I have an air reel already and ideally the wash hose can have a similar setup.
This unit is small enough that I would set it on a shelf (that I would have to add to the wall) near the water taps and run its hose to a reel. My fear is water pressure drop from that setup, I have no interest in constantly rolling/unrolling the cord and water line for this since I already have to deal with that and it wouldn't be an upgrade in that case
Works great with a foam cannon, watch some of the YouTube reviews.
Originally Posted by Striker223
My electric weed wacker has been massively more expensive than gas and it just doesn't have enough charge on one battery. Total system cost was over $700 and it managed to kill a battery that was $230.....
If I did it again I would still buy it though because I hate two stroke engines. It's just massively expensive for lower performance and lifespan, only reason I did it was I upgraded my cordless batteries to the newest standard and had the old extras to power it.
How many weeds are you whacking?! I have electric battery lawn tools and never run out of charge. $700? What unit do you have? I think mine was $150.
Originally Posted by LeX2K
You really think this cord will have pure copper 14 gauge wire? Most likely 75 watts will be dissipated by the power cord alone.
edit - your resistance figure is 2x too low.
Its a consumer product, I have zero concerns about its safety lol
I remember when I was a kid my mom bumped into one of those Fleetwoods with her Aerostar van. Very minor damage to the rear taillight, but the woman went NUTS! "Oh my Fleetwood Cadillac!" she kept yelling, I can still see it lol
Unless you have multiple high-current items actually running simultaneously, it shouldn't be an issue. So don't run the pressure washer AND your compressor AND a worm drive saw at the same time on the same circuit.
Already was tripping the circuit lol! That's why I ran a second one out there for the compressor, the one the house came with is the WHOLE garage other than lights and openers.....I also always have some stuff plugged in so I would probably trip it again if I didn't make sure to only use the washer. Compressor outlet is too far for me to want to use
Works great with a foam cannon, watch some of the YouTube reviews.
How many weeds are you whacking?! I have electric battery lawn tools and never run out of charge. $700? What unit do you have? I think mine was $150.
Its a consumer product, I have zero concerns about its safety lol
Whole yard perimeter and other stuff, I use the M18 Milwaukee unit with the edger head and shrub head. When I mow I use the string spiny head to do all the areas the mower doesn't get to plus the sides of the drive and swap to the other heads on weeks that I need to maintain the other stuff. Batteries are VERY expensive and they don't last, first set is dying already.....meanwhile my gas blower, mower, and snowblower are all over 15 years old with no issues. Again the only reason I even tried was because 1. I already had batteries from my work tools and 2. the POS two stoke thing I had before made me go into a full on rage and slam it overhead into the concrete x10 times, for that alone I will not go back to two stroke garbage.