What kind of RWHP gains do you think you will see with the engine/exhaust upgrades?
Project: COLOSUS
Thread Starter
Pole Position
iTrader: (3)
Joined: Mar 2007
Posts: 309
Likes: 5
From: Edmonton area, Alberta
Project: COLOSUS
Detials:
1991 Toyota Celsior
125,000kms
Black exterior
Tan Interior
19" Lowenhart rims
JIC Magic coilovers
Plans:
1. K&N filter & intake mod
2. Pioneer GPS
3. Billet Grill
4. JP rear cans
5. Battery Relocation to trunk
6. S&S headers
7. Custom 2.5" exhaust from headers to cans (cat, resonator & pre-mufflers all deleted)
8. Bullet Supercharger Kit
9. Nology Spark plug wires and NGK plugs
10. Water/Methanol injection kit
11. custom gauge mount (boost, egt, a/f)
12. strut braces (front and rear)
13. new tires... lol
.
.
.
urethane bushings, engine damper, brake master cylinder stopper, supra brake upgrade, stainless brake lines, etc.
1991 Toyota Celsior
125,000kms
Black exterior
Tan Interior
19" Lowenhart rims
JIC Magic coilovers
Plans:
1. K&N filter & intake mod
2. Pioneer GPS
3. Billet Grill
4. JP rear cans
5. Battery Relocation to trunk
6. S&S headers
7. Custom 2.5" exhaust from headers to cans (cat, resonator & pre-mufflers all deleted)
8. Bullet Supercharger Kit
9. Nology Spark plug wires and NGK plugs
10. Water/Methanol injection kit
11. custom gauge mount (boost, egt, a/f)
12. strut braces (front and rear)
13. new tires... lol
.
.
.
urethane bushings, engine damper, brake master cylinder stopper, supra brake upgrade, stainless brake lines, etc.
Last edited by Boyscout; Jun 4, 2014 at 05:35 AM.
Thread Starter
Pole Position
iTrader: (3)
Joined: Mar 2007
Posts: 309
Likes: 5
From: Edmonton area, Alberta
Current Progress:
Im also thinking i will lower the front of the car 1/2" to make the wheel well gap a little less. I cant lower the car in the rear without rolling the fenders. (i only have 1/2" clearance in the rear because of the 275's...and i dont particularly want to roll the fenders)
Im also thinking i will lower the front of the car 1/2" to make the wheel well gap a little less. I cant lower the car in the rear without rolling the fenders. (i only have 1/2" clearance in the rear because of the 275's...and i dont particularly want to roll the fenders)
Trending Topics
ClubLexus Stories
Celebrating Lexus & Toyota from Around the Globe
Lexus NX 350h: A Fuel-Sipping Secret Hot Hatch???
Michael S. Palmer
5 Best & 5 Worst Lexus Daily Drivers
Joe Kucinski
Top 5 Hottest Lexus & Toyotas in 2026 (Hardest To Buy)
Brett Foote
2026 Lexus IS 350 F Sport Review: The Last of Its Kind Still Rocks
Michael S. Palmer
Top 10 Most Confusing Things Lexus Has Ever Done!
Joe Kucinski
2026 Lexus ES Review: Lexus Re-Embraces Founding Principles
Michael S. Palmer
10 Lexus Bargains That are Cheaper Than a New Toyota RAV4
Joe Kucinski
8 Weirdest Things Lexus Has Ever Built
Verdad Gallardo
10 Lexus Designs That Have Aged Like Fine Wine
Verdad Gallardo
Thread Starter
Pole Position
iTrader: (3)
Joined: Mar 2007
Posts: 309
Likes: 5
From: Edmonton area, Alberta
1/2 an inch lower in the front wont make the car look retarded...it will just make the wheel well gap a bit smaller which will make the car look like it has a proper stance...right now it looks too high in the front end (i swapped the front coil springs and they are a bit taller then the ones that came out)
Thread Starter
Pole Position
iTrader: (3)
Joined: Mar 2007
Posts: 309
Likes: 5
From: Edmonton area, Alberta
reieved these parts yesterday:
- Battery Box
- Strut brace
I was thinking of removing the factory CD changer and trim from the right side of the trunk...the battery box should fit nicely. then i will just make some custom trim to make it look "finished". (the box is stainless...it just has a white protective film on it)
- Battery Box
- Strut brace
I was thinking of removing the factory CD changer and trim from the right side of the trunk...the battery box should fit nicely. then i will just make some custom trim to make it look "finished". (the box is stainless...it just has a white protective film on it)
Last edited by Boyscout; Sep 12, 2011 at 01:38 PM.
