Crossmember brace broken. What does it do?
#1
Driver School Candidate
Thread Starter
Crossmember brace broken. What does it do?
Hey guys,
I started a thread about my issue, but it was deleted before I could finish reading the responses. Don't know why that happened, anyway. I found a broken crossmember brace under the front of my 02 gs430. Looks like water from the A/C hose was dripping directly onto the brace and rusted her through. My question, what does the brace actually support, can I remove it and still drive while I wait for a replacement and when can I get a used one for cheap? I really don't need the aftermarket ones right now. I'm just starting a new job and can't justify spending over $200 bucks for the upgrade. Thanks guys. Oh here are some pics...
I started a thread about my issue, but it was deleted before I could finish reading the responses. Don't know why that happened, anyway. I found a broken crossmember brace under the front of my 02 gs430. Looks like water from the A/C hose was dripping directly onto the brace and rusted her through. My question, what does the brace actually support, can I remove it and still drive while I wait for a replacement and when can I get a used one for cheap? I really don't need the aftermarket ones right now. I'm just starting a new job and can't justify spending over $200 bucks for the upgrade. Thanks guys. Oh here are some pics...
#3
Sorry, but I think your in the wrong area. You should try posting in the 2nd gen GS. I can tell you though that a cross member is impotent. It helps the rigidity of the car and will effect the handling of your car.
#4
Driver School Candidate
Thread Starter
Sorry
Sorry. I thought I was posting under gs430. Thanks for your help
#5
Lexus Champion
iTrader: (10)
Hey guys,
I started a thread about my issue, but it was deleted before I could finish reading the responses. Don't know why that happened, anyway. I found a broken crossmember brace under the front of my 02 gs430. Looks like water from the A/C hose was dripping directly onto the brace and rusted her through. My question, what does the brace actually support, can I remove it and still drive while I wait for a replacement and when can I get a used one for cheap? I really don't need the aftermarket ones right now. I'm just starting a new job and can't justify spending over $200 bucks for the upgrade. Thanks guys. Oh here are some pics...
I started a thread about my issue, but it was deleted before I could finish reading the responses. Don't know why that happened, anyway. I found a broken crossmember brace under the front of my 02 gs430. Looks like water from the A/C hose was dripping directly onto the brace and rusted her through. My question, what does the brace actually support, can I remove it and still drive while I wait for a replacement and when can I get a used one for cheap? I really don't need the aftermarket ones right now. I'm just starting a new job and can't justify spending over $200 bucks for the upgrade. Thanks guys. Oh here are some pics...
#6
Hey guys,
I started a thread about my issue, but it was deleted before I could finish reading the responses. Don't know why that happened, anyway. I found a broken crossmember brace under the front of my 02 gs430. Looks like water from the A/C hose was dripping directly onto the brace and rusted her through. My question, what does the brace actually support, can I remove it and still drive while I wait for a replacement and when can I get a used one for cheap? I really don't need the aftermarket ones right now. I'm just starting a new job and can't justify spending over $200 bucks for the upgrade. Thanks guys. Oh here are some pics...
I started a thread about my issue, but it was deleted before I could finish reading the responses. Don't know why that happened, anyway. I found a broken crossmember brace under the front of my 02 gs430. Looks like water from the A/C hose was dripping directly onto the brace and rusted her through. My question, what does the brace actually support, can I remove it and still drive while I wait for a replacement and when can I get a used one for cheap? I really don't need the aftermarket ones right now. I'm just starting a new job and can't justify spending over $200 bucks for the upgrade. Thanks guys. Oh here are some pics...
From looking at that particular brace its setup to prevent front to rear movement, so you should notice a difference in that the steering being a bit shakey, or odd movements when hitting a pothole or cornering with a good degree of force on that side of the car.
If you're planning on leaving it for a bit, I would cut away the broken portion next to your resonator/cat to prevent it from puncturing the exhaust under movement.
As others have said that piece is there for stability and probably some degree of frontal crash worthiness but it doesn't appear to be directly supporting the weight of any critical components. The only thing I could see happening is the front crossmember shifting backwards due to impacts on that tire which will throw out your alignment eventually and **may** cause some residual damaged eventually to your steering rack or tie rods... unlikely but possible with a big impact.
In all aside from the potential to puncture the exhaust I wouldn't worry about it too much if you need a couple months to get it fixed. Just treat the car nicely and avoid potholes and you should be ok to limp along.
The following users liked this post:
QLex300 (02-07-22)
#7
Driver School Candidate
Thread Starter
Use my advice at your own risk.
From looking at that particular brace its setup to prevent front to rear movement, so you should notice a difference in that the steering being a bit shakey, or odd movements when hitting a pothole or cornering with a good degree of force on that side of the car.
If you're planning on leaving it for a bit, I would cut away the broken portion next to your resonator/cat to prevent it from puncturing the exhaust under movement.
As others have said that piece is there for stability and probably some degree of frontal crash worthiness but it doesn't appear to be directly supporting the weight of any critical components. The only thing I could see happening is the front crossmember shifting backwards due to impacts on that tire which will throw out your alignment eventually and **may** cause some residual damaged eventually to your steering rack or tie rods... unlikely but possible with a big impact.
In all aside from the potential to puncture the exhaust I wouldn't worry about it too much if you need a couple months to get it fixed. Just treat the car nicely and avoid potholes and you should be ok to limp along.
From looking at that particular brace its setup to prevent front to rear movement, so you should notice a difference in that the steering being a bit shakey, or odd movements when hitting a pothole or cornering with a good degree of force on that side of the car.
If you're planning on leaving it for a bit, I would cut away the broken portion next to your resonator/cat to prevent it from puncturing the exhaust under movement.
As others have said that piece is there for stability and probably some degree of frontal crash worthiness but it doesn't appear to be directly supporting the weight of any critical components. The only thing I could see happening is the front crossmember shifting backwards due to impacts on that tire which will throw out your alignment eventually and **may** cause some residual damaged eventually to your steering rack or tie rods... unlikely but possible with a big impact.
In all aside from the potential to puncture the exhaust I wouldn't worry about it too much if you need a couple months to get it fixed. Just treat the car nicely and avoid potholes and you should be ok to limp along.
Trending Topics
#8
Driver School Candidate
Thread Starter
Fixed
Use my advice at your own risk.
From looking at that particular brace its setup to prevent front to rear movement, so you should notice a difference in that the steering being a bit shakey, or odd movements when hitting a pothole or cornering with a good degree of force on that side of the car.
If you're planning on leaving it for a bit, I would cut away the broken portion next to your resonator/cat to prevent it from puncturing the exhaust under movement.
As others have said that piece is there for stability and probably some degree of frontal crash worthiness but it doesn't appear to be directly supporting the weight of any critical components. The only thing I could see happening is the front crossmember shifting backwards due to impacts on that tire which will throw out your alignment eventually and **may** cause some residual damaged eventually to your steering rack or tie rods... unlikely but possible with a big impact.
In all aside from the potential to puncture the exhaust I wouldn't worry about it too much if you need a couple months to get it fixed. Just treat the car nicely and avoid potholes and you should be ok to limp along.
From looking at that particular brace its setup to prevent front to rear movement, so you should notice a difference in that the steering being a bit shakey, or odd movements when hitting a pothole or cornering with a good degree of force on that side of the car.
If you're planning on leaving it for a bit, I would cut away the broken portion next to your resonator/cat to prevent it from puncturing the exhaust under movement.
As others have said that piece is there for stability and probably some degree of frontal crash worthiness but it doesn't appear to be directly supporting the weight of any critical components. The only thing I could see happening is the front crossmember shifting backwards due to impacts on that tire which will throw out your alignment eventually and **may** cause some residual damaged eventually to your steering rack or tie rods... unlikely but possible with a big impact.
In all aside from the potential to puncture the exhaust I wouldn't worry about it too much if you need a couple months to get it fixed. Just treat the car nicely and avoid potholes and you should be ok to limp along.
#10
So just grind off or bend that tab down to increase the clearance if that is the part which is interfering.
The following users liked this post:
QLex300 (02-07-22)
#11
Driver School Candidate
Thread Starter
Thank you
If you look at your before and after pictures you'll see the new brace has an extra mounting tab in the center by the transmission... My guess is it's that tab which is hitting the transmission when it vibrates in reverse. That would be my only guess based off the pictures you uploaded.
So just grind off or bend that tab down to increase the clearance if that is the part which is interfering.
So just grind off or bend that tab down to increase the clearance if that is the part which is interfering.
The following users liked this post:
QLex300 (02-07-22)
#12
You're welcome! I'm glad it worked out and that's all it was.
Those ones are much harder from afar =) Clunk over bump could be a number of things from wheel bearings to bent shocks to worn u joints in the driveshaft. You'll probably need a real mechanic for that, but if it's only on bumps it's probably not horrible to leave it be.
If it's whining it could be drive belt squeal; simply adjusting the drive belt tensioner (or if its autotensioning replacing that part) should be sufficient... or if the belt is frayed or damaged simply replacing it. But you probably want to have a mechanic do that if you don't have a torque wrench.
Good luck!
If it's whining it could be drive belt squeal; simply adjusting the drive belt tensioner (or if its autotensioning replacing that part) should be sufficient... or if the belt is frayed or damaged simply replacing it. But you probably want to have a mechanic do that if you don't have a torque wrench.
Good luck!
Thread
Thread Starter
Forum
Replies
Last Post
D2-AUTOSPORT
Wheels, Tires & Brakes Forum
7
08-23-05 05:15 PM