Project Mu Pads
#256
Racer
wow, lol just realized no one replied to my question so I'll answer myself.
The pads are making good contact now. It's been over a year and 8 months now and these pads are still holding strong with a lot of meat left.
The pads are making good contact now. It's been over a year and 8 months now and these pads are still holding strong with a lot of meat left.
#257
Former Sponsor
iTrader: (1)
-Matt M.
#258
I got the Type NS pads straight from Japan, which ended up being cheaper than buying from one of the CL vendors thanks to the weak CAD, but that's another story.
So far the pads have not adjusted to the rotor's existing and somewhat odd wavy wear pattern - hoping this ugly inner ring will go away soon. It's present on both fronts, but the rears look good on the other hand. A full bed-in has been performed after the install.
So far the pads have not adjusted to the rotor's existing and somewhat odd wavy wear pattern - hoping this ugly inner ring will go away soon. It's present on both fronts, but the rears look good on the other hand. A full bed-in has been performed after the install.
#260
Racer
From what I remember when I had these pads installed I had a similar pattern the first few times I drove with them. I do believe they go away after more use.
#261
I just installed new NS400 pads & Project Mu rotors. Did anyone use any grease of any form for noise reduction?
Reason I ask, is that I didn't. Mine were quite loud during the initial bed in, & over the last 250km (first 250km since I put the pads in) they've quietened down a lot, but are still a bit noisy at times. Is this normal? Will it go away completely after more kms/miles?
Other than that, I'm VERY happy with them. Not as bitey as the OEM pads, but still feel good. The reduction in brake dust is fantastic!
Reason I ask, is that I didn't. Mine were quite loud during the initial bed in, & over the last 250km (first 250km since I put the pads in) they've quietened down a lot, but are still a bit noisy at times. Is this normal? Will it go away completely after more kms/miles?
Other than that, I'm VERY happy with them. Not as bitey as the OEM pads, but still feel good. The reduction in brake dust is fantastic!
#262
Lexus Test Driver
iTrader: (1)
I just installed new NS400 pads & Project Mu rotors. Did anyone use any grease of any form for noise reduction?
Reason I ask, is that I didn't. Mine were quite loud during the initial bed in, & over the last 250km (first 250km since I put the pads in) they've quietened down a lot, but are still a bit noisy at times. Is this normal? Will it go away completely after more kms/miles?
Other than that, I'm VERY happy with them. Not as bitey as the OEM pads, but still feel good. The reduction in brake dust is fantastic!
Reason I ask, is that I didn't. Mine were quite loud during the initial bed in, & over the last 250km (first 250km since I put the pads in) they've quietened down a lot, but are still a bit noisy at times. Is this normal? Will it go away completely after more kms/miles?
Other than that, I'm VERY happy with them. Not as bitey as the OEM pads, but still feel good. The reduction in brake dust is fantastic!
-Mike
#263
Former Sponsor
iTrader: (1)
The pads should not be producing any noise after a proper bed in procedure. Do you mind briefly explaining how you bedded them in? If for whatever reason you can't get the noise to disappear with bedding alone then mikersoft's suggestion should also be helpful eliminating the noise.
-Matt M.
-Matt M.
#264
#265
Guys, was anybody using Project Mu HC+ pads on IS-F?
They are supposed to be kind of dual-purpose pad. I had them once on the rear of my e90 330i, but I'm really curious how they would work with heavy IS-F on the front with OEM rotors.
They are supposed to be kind of dual-purpose pad. I had them once on the rear of my e90 330i, but I'm really curious how they would work with heavy IS-F on the front with OEM rotors.
#266
The pads should not be producing any noise after a proper bed in procedure. Do you mind briefly explaining how you bedded them in? If for whatever reason you can't get the noise to disappear with bedding alone then mikersoft's suggestion should also be helpful eliminating the noise.
-Matt M.
-Matt M.
Step 1: Make 10 stops from 30 mph down to about 10 mph using moderate braking pressure and allowing approximately 30 seconds between stops for cooling. Do not drag your pads during these stops.
Step 2: Make 5 consecutive stops from 50 mph down to 10 mph . After the 5th stop, allow your braking system to cool for approximately 30 minutes. This completes the break-in of your pads to the rotor surface.
During Steps 1 & 2, a de-gassing process occurs which may produce an odor coming from your pads as they complete the break-in cycle. This odor is normal and is part of the process your pads must go through to achieve their ultimate level of performance. The odor will go away after allowing your braking system to cool for approximately 30 minutes.
#267
I think I posted earlier in the thread a while back when I first put my Project Mu's in. Mine squealed like a pig in heat at first and it would not stop even after applying anti squeal 2 times. Eventually it just went away after about 4K km's of driving. I can only hear them squeal at low speed once of twice a week if that sometimes.
#268
Former Sponsor
iTrader: (1)
Most of the IS-F guys are after a low dusting, silent street pad. The guys that track pretty heavily swap in full track pads but I am staring to notice more guys who are willing to compromise on the dust levels for greater performance in aggressive street use and possibly even some occasional track use. We love the Endless MX72 for this type of use but the Project Mu HC+ is a lower cost alternative to the MX72. We don't normally stock the HC+ for in the IS-F pad shapes but if there is enough interest we can look into placing a large order and doing a group buy.
-Matt M.
#269
Former Sponsor
iTrader: (1)
I basically followed the below. The rotors don't appear to be wearing in any unorthodox way. As mentioned, the sound is decreasing, just hopeful it mostly goes away.
Step 1: Make 10 stops from 30 mph down to about 10 mph using moderate braking pressure and allowing approximately 30 seconds between stops for cooling. Do not drag your pads during these stops.
Step 2: Make 5 consecutive stops from 50 mph down to 10 mph . After the 5th stop, allow your braking system to cool for approximately 30 minutes. This completes the break-in of your pads to the rotor surface.
During Steps 1 & 2, a de-gassing process occurs which may produce an odor coming from your pads as they complete the break-in cycle. This odor is normal and is part of the process your pads must go through to achieve their ultimate level of performance. The odor will go away after allowing your braking system to cool for approximately 30 minutes.
Step 1: Make 10 stops from 30 mph down to about 10 mph using moderate braking pressure and allowing approximately 30 seconds between stops for cooling. Do not drag your pads during these stops.
Step 2: Make 5 consecutive stops from 50 mph down to 10 mph . After the 5th stop, allow your braking system to cool for approximately 30 minutes. This completes the break-in of your pads to the rotor surface.
During Steps 1 & 2, a de-gassing process occurs which may produce an odor coming from your pads as they complete the break-in cycle. This odor is normal and is part of the process your pads must go through to achieve their ultimate level of performance. The odor will go away after allowing your braking system to cool for approximately 30 minutes.
I think I posted earlier in the thread a while back when I first put my Project Mu's in. Mine squealed like a pig in heat at first and it would not stop even after applying anti squeal 2 times. Eventually it just went away after about 4K km's of driving. I can only hear them squeal at low speed once of twice a week if that sometimes.
-Matt M.
Last edited by SpeedFreaksUSA; 09-03-15 at 01:51 PM.
Thread
Thread Starter
Forum
Replies
Last Post