ClubLexus - Lexus Forum Discussion
0 2022/02/19 11:46:09
0 2022/02/19 11:48:44
Steering Damper at mounting bracket
Steering Damper at mounting bracket
0 2022/02/19 11:49:26
0 2022/02/19 11:51:00
35330-50020 is transmission screen...
35330-50020 is transmission screen...
0 2022/02/20 07:23:46
0 2022/02/20 07:32:34
Please select the items you require
Please select the items you require
0 2022/02/20 07:32:35
0 2022/02/20 08:08:25
0 2022/02/20 08:08:27
0 2022/02/20 08:08:29
0 2022/02/20 08:30:00
0 2022/02/20 08:30:03
0 2022/02/20 08:30:06
0 2022/02/20 08:31:50
South America Spec in box
South America Spec in box
0 2022/02/20 19:43:01
0 2022/02/20 19:44:17
51446-50030
51446-50030
0 2022/02/20 19:44:51
51447-50011 or 5144750010
51447-50011 or 5144750010
0 2022/02/20 19:45:53
0 2022/02/21 16:23:57
0 2022/02/21 16:23:58
0 2022/02/22 21:45:53
SAC:280 883
SAC:280 883
0 2022/02/23 11:19:42
0 2022/02/23 16:02:53
1990 - 1994 LS400 rear suspensionparts diagram depicting a second insulator at bottom of spring 48258-50010
1990 - 1994 LS400 rear suspensionparts diagram depicting a second insulator at bottom of spring 48258-50010
0 2022/02/23 16:04:24
0 2022/02/23 16:07:40
0 2022/02/23 16:08:14
0 2022/02/23 16:10:32
0 2022/02/23 16:12:16
Only 5mm thick.
Only 5mm thick.
0 2022/02/23 16:12:46
73.5 mm inner diameter.
73.5 mm inner diameter.
0 2022/02/23 16:14:38
0 2022/02/23 16:16:26
2001-2006 rear suspension depicting a secondary upper insulator or plate between the bellows and spring
2001-2006 rear suspension depicting a secondary upper insulator or plate between the bellows and spring
0 2022/02/23 16:19:20
The extra insulator or plate appears to contour to the coil spring end to prevent extruding the upper bellows/insulator .
The extra insulator or plate appears to contour to the coil spring end to prevent extruding the upper bellows/insulator .
0 2022/02/23 16:19:22
0 2022/02/23 16:27:02
0 2022/02/24 15:07:53
Front side grommet/clip mold-marked 50840.
Front side grommet/clip mold-marked 50840.
0 2022/03/06 14:28:05
Mold mark 3 and what appears to be a logo in harness trough.
Mold mark 3 and what appears to be a logo in harness trough.
0 2022/03/06 14:28:11
Backside of grommet/clip.
Backside of grommet/clip.
0 2022/03/06 14:28:15
Backside image of door panel. To access plastic door pocket and preserve the gray foam insulator, used a curved Dremel scalpel knife to separate the factory glue from the plastic map pocket.
Backside image of door panel. To access plastic door pocket and preserve the gray foam insulator, used a curved Dremel scalpel knife to separate the factory glue from the plastic map pocket.
0 2022/03/06 18:11:34
0 2022/03/06 18:15:43