ClubLexus - Lexus Forum Discussion
0 2014/11/23 14:09:17
0 2014/11/23 14:09:14
0 2014/11/23 14:09:11
0 2014/11/23 14:09:09
0 2014/11/23 14:09:06
0 2014/11/23 14:09:04
0 2014/11/23 14:09:02
0 2014/11/23 14:09:00
0 2014/11/23 14:08:59
0 2014/11/23 14:08:57
0 2014/11/23 14:08:56
0 2014/11/23 14:08:55
0 2014/11/23 14:08:54
0 2014/11/16 12:32:23
0 2014/11/16 12:32:21
0 2014/11/16 12:32:19
0 2014/11/16 12:32:18
0 2014/11/16 12:32:16
Okay this stuff is not going all the way around the headlight and I did not cut it before the install.
Okay this stuff is not going all the way around the headlight and I did not cut it before the install.
0 2014/11/16 12:32:14
Not sure if you can make out the lines, but this is a one piece with a separated wing that wraps around the side. $74.31 I think they may have a bit of a profit margin here 😊
Not sure if you can make out the lines, but this is a one piece with a separated wing that wraps around the side. $74.31 I think they may have a bit of a profit margin here 😊
0 2014/11/16 12:32:12
Invisiblemask $74.31 they have three levels of quality and this is their best.
Invisiblemask $74.31 they have three levels of quality and this is their best.
0 2014/11/16 12:32:11
Alright… I have had enough of looking at my poor installation fail. I removed it and moved on to the next product.
Alright… I have had enough of looking at my poor installation fail. I removed it and moved on to the next product.
0 2014/11/16 12:32:09
The seam gap is too obvious to me and and I have some discoloration at the seam gap, probably due to the heat gun
The seam gap is too obvious to me and and I have some discoloration at the seam gap, probably due to the heat gun
0 2014/11/16 12:32:07
This is what I used to bond it.
This is what I used to bond it.
0 2014/10/26 13:42:28
I pulled the plastic bumper back and scuffed it up with a grinder.
I pulled the plastic bumper back and scuffed it up with a grinder.
0 2014/10/26 13:42:24
This is what it eventually came to look like.
This is what it eventually came to look like.
0 2014/10/26 13:42:22
Three weeks later it is still holding up. Artificial lighting so details are limited.
Three weeks later it is still holding up. Artificial lighting so details are limited.
0 2014/10/25 17:24:31
This is what I used.
This is what I used.
0 2014/10/25 17:03:20
High-tech compression LOL
High-tech compression LOL
0 2014/10/25 17:03:18
I went into the fender well and pulled the plastic off but could not find a good resolution. So Iused a grinder/sander to scuff up the area for the epoxy.
I went into the fender well and pulled the plastic off but could not find a good resolution. So Iused a grinder/sander to scuff up the area for the epoxy.
0 2014/10/25 17:03:15
0 2014/10/25 17:03:13
0 2014/10/22 16:00:04
0 2014/10/22 16:00:01
Oh,6x9s sweet
Oh,6x9s sweet
0 2014/10/22 15:59:59
0 2014/10/12 15:38:41
0 2014/10/12 15:38:39
0 2014/10/12 15:37:19
0 2015/05/05 17:10:50
0 2015/05/05 19:34:42
0 2015/05/06 17:13:21