ClubLexus - Lexus Forum Discussion
I'm still trying to figure out where this thing mounts / sits. Maybe it's bent out of shape?
I'm still trying to figure out where this thing mounts / sits. Maybe it's bent out of shape?
0 2021/02/11 20:28:47
0 2021/02/11 20:28:52
0 2021/02/11 20:28:55
0 2021/02/11 20:28:59
0 2021/02/12 10:27:58
0 2021/02/12 10:28:41
0 2021/02/12 10:29:44
0 2021/02/13 20:05:26
0 2021/02/13 20:05:31
The suspension ecu is the one on the right with the top plug disconnected. The nuts that hold it in are tucked in there pretty tight. I'm really glad I didn't remove it. I did slave in a replacement ecu before ohming out the wires. There is enough slack in the wires to plug in a new ecu without removing the original. The ecu obviously didn't fix the issue.
The suspension ecu is the one on the right with the top plug disconnected. The nuts that hold it in are tucked in there pretty tight. I'm really glad I didn't remove it. I did slave in a replacement ecu before ohming out the wires. There is enough slack in the wires to plug in a new ecu without removing the original. The ecu obviously didn't fix the issue.
0 2021/02/13 20:05:34
I'm still messing with the drivers mirror :/
I'm still messing with the drivers mirror :/
0 2021/02/13 20:05:37
I wonder what else I can take apart :)
I wonder what else I can take apart :)
0 2021/02/13 20:05:40
I chopped the plug off to work on inside.
I chopped the plug off to work on inside.
0 2021/02/13 20:05:43
Trying to avoid more work.
Trying to avoid more work.
0 2021/02/13 20:05:47
solder time
solder time
0 2021/02/13 20:05:51
0 2021/02/13 20:05:55
Looks fine but it's not.
Looks fine but it's not.
0 2021/02/13 20:05:58
Not all were broken at the bottom of the pin.
Not all were broken at the bottom of the pin.
0 2021/02/13 20:06:02
0 2021/02/13 20:06:05
0 2021/02/13 20:06:09
The copper wire is broken internally.
The copper wire is broken internally.
0 2021/02/13 20:06:12
0 2021/02/13 20:06:15
0 2021/02/13 20:06:18
IMO this heat shrink wasn't really required. Doesn't hurt though.
IMO this heat shrink wasn't really required. Doesn't hurt though.
0 2021/02/13 20:06:22
0 2021/02/13 20:06:26
I wrapped each joint individually with electrical tape too.
I wrapped each joint individually with electrical tape too.
0 2021/02/13 20:06:30
All of this got wrapped in electrical tape to create one bundle.
All of this got wrapped in electrical tape to create one bundle.
0 2021/02/13 20:06:34
0 2021/02/13 20:06:37
The original rubber shield is on it plus a few layers of electrical tape :)
The original rubber shield is on it plus a few layers of electrical tape :)
0 2021/02/13 20:06:41
Done!
Done!
0 2021/02/13 20:06:44
I was clearing codes when I realized this was not a current code. Happy dance.
I was clearing codes when I realized this was not a current code. Happy dance.
0 2021/02/13 20:30:35
All are 17
All are 17
0 2021/02/13 20:30:45
I tested both left and right front dampers. They both adjust using techstream now. It's interesting that when one circuit fails all are disabled by the ecu.
I tested both left and right front dampers. They both adjust using techstream now. It's interesting that when one circuit fails all are disabled by the ecu.
0 2021/02/13 20:30:53
0 2021/02/14 21:07:54
0 2021/02/14 21:08:05
0 2021/02/14 21:11:37
0 2021/02/14 23:00:47
0 2021/02/14 23:01:07
0 2021/02/15 17:14:35
0 2021/02/15 18:15:40