Roll-up ramp recommendation for near stock height SC300 with 97+ OEM front bumper
#1
Roll-up ramp recommendation for near stock height SC300 with 97+ OEM front bumper
Hey all,
I'd like to get some under-engine access to my SC to do a little work and my garage space is too narrow and smooth to use a 3-ton hydraulic jack and stands safely. I've always used stands and a big truck jack in the past to get access under the car but I thought I might go with a set of roll-up ramps this time due to my space and surface constraints. They seem like they'd be safer and faster to use with a spotter.
I have learned Corvette owners love the RaceRamps products with the many versions and extender options available since their cars are so low but I really just want to get some ramps that are inexpensive, sturdy and simple that works safely. I don't cheap out on quality tools when precision is needed but a lot of the time the most expensive option isn't needed.
I have a set of rear wheel chucks and Harbor Freight has a set of thick hard plastic ramps with integrated front chucks for $40.00 that look like they'd get the job done safely: "Magnum-16000 Auto Ramp Set With Built-In Safety Chock" (HF SKU# DAVRIC - Item#67722)
What I don't want to do is tear up my front bumper. I have an OEM 97+ type with no extra lip and my car is almost at a stock ride height front and rear... I'm about 1" lower than stock-- no more than that. Has anyone successfully used these or similar ramps with a nearly stock height SC? Further, does anyone have a good inexpensive ramp recommendation that is better? I like what RaceRamps sells but I don't currently want to spend $200++ on one of their products.
Thanks!
Here's what the HF ramp looks like:
I'd like to get some under-engine access to my SC to do a little work and my garage space is too narrow and smooth to use a 3-ton hydraulic jack and stands safely. I've always used stands and a big truck jack in the past to get access under the car but I thought I might go with a set of roll-up ramps this time due to my space and surface constraints. They seem like they'd be safer and faster to use with a spotter.
I have learned Corvette owners love the RaceRamps products with the many versions and extender options available since their cars are so low but I really just want to get some ramps that are inexpensive, sturdy and simple that works safely. I don't cheap out on quality tools when precision is needed but a lot of the time the most expensive option isn't needed.
I have a set of rear wheel chucks and Harbor Freight has a set of thick hard plastic ramps with integrated front chucks for $40.00 that look like they'd get the job done safely: "Magnum-16000 Auto Ramp Set With Built-In Safety Chock" (HF SKU# DAVRIC - Item#67722)
What I don't want to do is tear up my front bumper. I have an OEM 97+ type with no extra lip and my car is almost at a stock ride height front and rear... I'm about 1" lower than stock-- no more than that. Has anyone successfully used these or similar ramps with a nearly stock height SC? Further, does anyone have a good inexpensive ramp recommendation that is better? I like what RaceRamps sells but I don't currently want to spend $200++ on one of their products.
Thanks!
Here's what the HF ramp looks like:
Last edited by KahnBB6; 10-12-17 at 12:17 AM.
#2
Lead Lap
iTrader: (8)
The thing that makes the race ramps effective is their length. It allows you to gradually drive up an incline. Most of the cheaper plastic ones are too short and will hit our front bumpers. Personally, I use 2 floor jacks and lift at the front tow hook on one side to able to slide the 2nd jack to the center lift point.
The cheapest option is to build them out of wood, but it would be really heavy and you'd have to store these monsters somewhere.
https://www.clublexus.com/forums/is-...n-f-ramps.html
The cheapest option is to build them out of wood, but it would be really heavy and you'd have to store these monsters somewhere.
https://www.clublexus.com/forums/is-...n-f-ramps.html
#3
Advanced
iTrader: (1)
I picked up the Harbor Freight ramps a couple months ago.They're surprisingly good quality, especially for the price. I've used them with a RX350 & Volvo S80 and they worked great. I can't comment on how they are with SC's though, since my transmission is toast lol. I think you would scrape the front bumper though, considering how close the Volvo came to scraping.
#5
Thanks, guys! Hmm... it does seem like I'll be skirting a bad bumper scrape episode if I use anything BUT the expensive RaceRamps (although the 2x4 extension idea is a good one too). I need to research some more ramp products, then. The simplest answer seems to be the right one: we need a much longer/gradual than average incline angle with SC's so as not to damage our front bumpers.
As for right now I can work around not having any ramps or jacking to do what I need to in the engine bay. Appropriate ramps would just be a nice thing to have for some things or even just regular oil changes.
As for right now I can work around not having any ramps or jacking to do what I need to in the engine bay. Appropriate ramps would just be a nice thing to have for some things or even just regular oil changes.
#6
Lead Lap
iTrader: (8)
I've got a set of those HF ramps for trailer stuff. They appear to be solid enough, although I haven't used them yet. Honestly, I wouldn't get under a car with HF plastic holding it up... I've seen too much of their stuff fail. (I do trust their jacks and stands, though, so go figure.)
The biggest challenge with all the drive-up ramps is width. Most of them max out at around 8" between the lips. I can barely center my 225 front tires on the old set (can't recall the brand off hand) I've got. You really don't want to be pushing thousands of pounds over the side of something that can tip or buckle. To get anything in the 9-10" range jumps up in price dramatically.
The biggest challenge with all the drive-up ramps is width. Most of them max out at around 8" between the lips. I can barely center my 225 front tires on the old set (can't recall the brand off hand) I've got. You really don't want to be pushing thousands of pounds over the side of something that can tip or buckle. To get anything in the 9-10" range jumps up in price dramatically.
#7
^^ Yikes! Thank you for the heads up t2d2! My tires definitely will not fit on these. I have 235's in the front and there is no way my 275 rears would fit if 225's are difficult enough.
The RaceRamp products are sounding more ideal and proven the more you guys educate me in this thread. Still very expensive but it seems like a much better product if jack stands and a 3 ton hydraulic jack aren't feasible.
I guess with car ramps...you get what you pay for?
Thank you everyone for chiming in with good advice!
The RaceRamp products are sounding more ideal and proven the more you guys educate me in this thread. Still very expensive but it seems like a much better product if jack stands and a 3 ton hydraulic jack aren't feasible.
I guess with car ramps...you get what you pay for?
Thank you everyone for chiming in with good advice!
Trending Topics
#11
Instructor
iTrader: (1)
I have these. Hands down the best ramps I've ever seen.
I'm lowered and with these my bumper doesn't even touch the ramp.
Any time I need to mess around under the car I just whip these out and drive the car up onto them
https://raceramps.com/car-ramps/gara...xt-race-ramps/
I'm lowered and with these my bumper doesn't even touch the ramp.
Any time I need to mess around under the car I just whip these out and drive the car up onto them
https://raceramps.com/car-ramps/gara...xt-race-ramps/
The following users liked this post:
KahnBB6 (10-18-17)
#12
Instructor
iTrader: (1)
As for jackstands that won't slip, I use these when i need them.
Big Red aluminum jack stands. I originally got these because they were the only jacks that couldn't sink into the asphalt on my parents' driveway. They don't have rubber feet or anything, but they do have the largest footprint of a jackstand I've ever seen. The diameter of the base is 8 inches
http://www.torinjacksusa.com/bigred/...ck-stands.html
Big Red aluminum jack stands. I originally got these because they were the only jacks that couldn't sink into the asphalt on my parents' driveway. They don't have rubber feet or anything, but they do have the largest footprint of a jackstand I've ever seen. The diameter of the base is 8 inches
http://www.torinjacksusa.com/bigred/...ck-stands.html
The following users liked this post:
KahnBB6 (10-18-17)
#13
Lead Lap
iTrader: (8)
I have these. Hands down the best ramps I've ever seen.
I'm lowered and with these my bumper doesn't even touch the ramp.
Any time I need to mess around under the car I just whip these out and drive the car up onto them
https://raceramps.com/car-ramps/gara...xt-race-ramps/
I'm lowered and with these my bumper doesn't even touch the ramp.
Any time I need to mess around under the car I just whip these out and drive the car up onto them
https://raceramps.com/car-ramps/gara...xt-race-ramps/
As for jackstands that won't slip, I use these when i need them.
Big Red aluminum jack stands. I originally got these because they were the only jacks that couldn't sink into the asphalt on my parents' driveway. They don't have rubber feet or anything, but they do have the largest footprint of a jackstand I've ever seen. The diameter of the base is 8 inches
http://www.torinjacksusa.com/bigred/...ck-stands.html
Big Red aluminum jack stands. I originally got these because they were the only jacks that couldn't sink into the asphalt on my parents' driveway. They don't have rubber feet or anything, but they do have the largest footprint of a jackstand I've ever seen. The diameter of the base is 8 inches
http://www.torinjacksusa.com/bigred/...ck-stands.html
Thread
Thread Starter
Forum
Replies
Last Post
313sc3
SC- 1st Gen (1992-2000)
17
07-02-12 08:25 PM