Eye Lids
LOL
nice... now we'll be twins.... 
i would wait until spring to put them on... i re-did mine after i installed the halos and the cold is leaving air pockets in the vinyl no matter how much you smooth it down
i would wait until spring to put them on... i re-did mine after i installed the halos and the cold is leaving air pockets in the vinyl no matter how much you smooth it down
LOL guys thats only 25% of the colognes
But yes this is vinyl. bought from www.rvinyl.com.
And i will post pics after i put them on. But guys i have one more things to put on the heads using the vinyl i bought. I am planning to put 1" strip on the lower part of the headlight which will make only half of the turn signal to show. I will also do this tomorrow.
But yes this is vinyl. bought from www.rvinyl.com.
And i will post pics after i put them on. But guys i have one more things to put on the heads using the vinyl i bought. I am planning to put 1" strip on the lower part of the headlight which will make only half of the turn signal to show. I will also do this tomorrow.
Trending Topics
here's how i did mine.
i cut out a 2 ft by 5 inches strip
I take off the sheet so that the sticky side shows
wet my headlight
i put the whole 2 foot by 5 inch strip ON my headlight and then cut going along the body's lines and ect.
i cut the top but leave some room so i am able to crease the black film so no light will show because the black film will be inside the creases under the rubber and body part etc.
then after that i would cut the film ON the headlight.
a tedious job.
i didn't want any light showing and i said i'll do it for you but need your headlight to have it perfect
you also asked if you could pay me to make it for you
i declined payment and offered to do it for free if you come out to a NELOC meet.. not a bad trade i thought.
but i'm glad you made them...
yup... i remember you quite clearly and i will still stand by my word
here's how i did mine.
i cut out a 2 ft by 5 inches strip
I take off the sheet so that the sticky side shows
wet my headlight
i put the whole 2 foot by 5 inch strip ON my headlight and then cut going along the body's lines and ect.
i cut the top but leave some room so i am able to crease the black film so no light will show because the black film will be inside the creases under the rubber and body part etc.
then after that i would cut the film ON the headlight.
a tedious job.
i didn't want any light showing and i said i'll do it for you but need your headlight to have it perfect
you also asked if you could pay me to make it for you
i declined payment and offered to do it for free if you come out to a NELOC meet.. not a bad trade i thought.
but i'm glad you made them...
here's how i did mine.
i cut out a 2 ft by 5 inches strip
I take off the sheet so that the sticky side shows
wet my headlight
i put the whole 2 foot by 5 inch strip ON my headlight and then cut going along the body's lines and ect.
i cut the top but leave some room so i am able to crease the black film so no light will show because the black film will be inside the creases under the rubber and body part etc.
then after that i would cut the film ON the headlight.
a tedious job.
i didn't want any light showing and i said i'll do it for you but need your headlight to have it perfect
you also asked if you could pay me to make it for you
i declined payment and offered to do it for free if you come out to a NELOC meet.. not a bad trade i thought.
but i'm glad you made them...
LOL yes exactly LOL. But heres how i made mine. I got a 14" long piece of paper and dry erase marker. I Marked the headlight with the outline of where i want to keep the vinyl. the i soaked the paper with goo gone. The made the paper see thru. Then i laid the paper on the headlight which showed the outling of where i wanted the vinyl. Then i traced the lines, and then cut the paper. The finally traced it onto the vinyl sheet and wallah!!!!!
Perfect fit!
