GX - 1st Gen (2003-2009) Discussion topics related to the 2003 -2009 GX470 models

Side marker bulb burned out/replacement?

Thread Tools
 
Search this Thread
 
Old 02-17-17, 04:14 AM
  #1  
levinsoy
Driver
Thread Starter
 
levinsoy's Avatar
 
Join Date: Feb 2002
Location: MD
Posts: 163
Received 10 Likes on 10 Posts
Default Side marker bulb burned out/replacement?

The yellow strip on the headlight unit that is behind a pillar where only tiny hands or maybe needle nose pliers can fit. Any easy way to replace this 194 bulb but from the top with removal of all the covers, Low beam light, and with maybe needle nose pliers? Can you get to it from below if I have the SUV on a lift? Any help would be greatly appreciated as I have one out on the passenger side. I'm glad it's not on the drivers side as I would probably need to remove the battery to get to it.
Old 02-17-17, 05:51 AM
  #2  
chiph9
Pole Position
 
chiph9's Avatar
 
Join Date: Feb 2014
Location: NC
Posts: 3,444
Received 753 Likes on 617 Posts
Default

Find someone with small hands to come up from below.
Passenger side is easier than driver's side. Would probably be useful if your small-hand person were left-handed.

Chip H.
Old 02-18-17, 09:57 AM
  #3  
LoneHiker
Pit Crew
 
LoneHiker's Avatar
 
Join Date: Feb 2016
Location: CO
Posts: 191
Likes: 0
Received 25 Likes on 23 Posts
Default

I have large hands and had no problem changing this bulb from underneath (no lift needed). Mine were out on both sides so I know it works for both. Fears about this bulb's location are highly overrated. Get underneath and feel around for it, it's hard to reach up there and be able to see at the same time. But use common sense and you'll know which socket it is by feel. A quarter turn of the socket counterclockwise and pull it out and down so you can yank out the bulb and replace it. Putting it back into place is harder but still possible. Get it back into place and turn it just enough so that the socket doesn't fall back out of place. Then use a pair of needle nose pliers to grab it and twist it the rest of the way till the socket clicks.
The following users liked this post:
levinsoy (02-18-17)
Old 02-18-17, 04:40 PM
  #4  
levinsoy
Driver
Thread Starter
 
levinsoy's Avatar
 
Join Date: Feb 2002
Location: MD
Posts: 163
Received 10 Likes on 10 Posts
Default

So I was under the car with the creeper and had my hand on the socket for a while but just couldn't nudge it because I couldn't get a good grip on it so I went from the top (removed covers, unplugged my HID low beam bulb, and got in there with some needle-nose pliers in order to turn the socket).

Thanks everyone for the help!
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
gcam77
GX - 1st Gen (2003-2009)
8
07-11-18 08:07 AM
RAMBLER2
GS - 4th Gen (2013-2020)
10
05-12-18 01:48 PM
Irish239
ES - 5th Gen (2007-2012)
8
10-03-12 07:05 PM
SidhuGs300
GS - 2nd Gen (1998-2005)
6
07-18-11 02:32 AM
dbullen
LS - 1st and 2nd Gen (1990-2000)
2
01-31-03 10:07 AM



Quick Reply: Side marker bulb burned out/replacement?



All times are GMT -7. The time now is 05:57 PM.