Good post... Can a moderator go back and delete the random posts though? Let's keep ONLY the facts to keep this a clean thread (and potentially a sticky).

 

good call.....especially thos eif us with the Advox

 

i just thought too it'd also be nice for people with Air to show Drive Height and Aired Out height. Because you can get some pretty agro offsets on with air because of how the wheels tuck when you lay it out, but then at ride height the wheels jut back out and become a bit mexican sometimes. So it would be good for people to see how it looks day to day as well as in 'show mode' !

 

aint i cant seem to figure this out... your rear ride height is lower than my but has less negative camber than i do wtf? i need spacers bad haha, 5mm should just be right on point... i like how yours sit right now

 

Guys if you have questions about the setup, PM the person! This thread isn't going to get sticky'd if we keep mucking it up with questions and comments ( I know I'm not following my own guidance here....) .

Leave it to posting your just your setup so we don't have to wade through all the crap.

 

how about u post your set up then go from there aite.... i dont think this would become a sticky because for 1... the no one has bother to post up any of their specs for 3 pages 6 so far i didnt count....and 2 Picture REQUEST. Non-Air Tucked Wheels
havent been sticky with 88k views yet soooooooooooooo i doubt that this will be 1 of them but yeah imma shut up for now haha....

 

Seems like a good idea if we could keep it less cluttered and just facts/pics

 

Here is a pic of my rears at ride height , I need to take new pics of the front.

19x10 Leon Hardiritt Beil's Fenders shaved rolled and a lil pull

 

This is the look I'm trying to achieve..

Specs on your suspension??? offset, tire size....

 

Wheel Make/Model: XXR 009(installed 7-9-09, removed 20's and lowered this sucka back down!)
Wheel Size (F/R): 19x9.5"(R)(3" lip) 19x9"(F)(2" lip)
Wheel Offset (F/R): +35 both
Tire Size (F/R):235/35/19---265/30/19
Ride height from middle fender (F/R) : don't know....low tho!
Suspension:Tom's Racing Advox
Camber (F/R) :no in front-- is "yes" an answer....lol
Toe (F/R) : all good
Fender Mods: cut slightly in front, cut A LOT in rear
Spacers:nope
sorry for crappy pics.....cars dirty, camera lens was dirty....and so on. Anodized red lug nuts coming soon. Center caps are being powder coated black as of now.

 

Keep them coming!!!!!!!!!

 

Wheel Make/Model:Rota DPT (Flat Steel)
Wheel Size (F/R):18X9 all four
Wheel Offset (F/R):+42mm all four
Tire Size (F/R):245/40/18 & 275/35/18
Ride height from middle fender (F/R) : Huge ... were talkin' Monster Truck Gap
Suspension:Stock (for now)
Camber (F/R) :
Toe (F/R) :
Fender Mods:None
Spacers:None

 

Wheel Make/Model: MRR GT1's chrome
Wheel Size (F/R): 20x8.5 / 20x10
Wheel Offset (F/R): +35(+30) / +43(+18)
Tire Size (F/R): 245/30/20 / 275/30/20
Ride height from middle fender (F/R) : 25.5in / 26in
Suspension: Tein SS coils, Exact Motorsport Camber spacers / SPC rear camber bolt
Camber (F/R) : -1.75 / -1.25
Toe (F/R) : +0.10 / -0.08
Fender Mods: fenders rolled front and rear
Spacers: +5mm for front and +25mm for rear





Winter setup
Wheel Make/Model: Sora'T
Wheel Size (F/R): 17x8 / 17x8
Wheel Offset (F/R): +25(+20) / +20(+0)
Tire Size (F/R): 235/45/17 / 235/45/17
Spacers: +5mm for front and +25mm for rear

 

looks like a lot of people still aren't getting the message. Keep 'em coming

 

hey insomniac, cuz i was curious, i tried running the +15mm spacers up front, they work, rubb like crazy (on fender liner) but they work.

talked to jun, he said i could always just cut away at the fender liner, and cut the fender a bit (i rolled mine but the fronts aren't exactly flat)

so i think max for 8.5's are about +20 for the fronts with under -2 degree camber.