Last edit by: IB Advertising
See related guides and technical advice from our community experts:
Browse all: Lexus IS Lighting Guides
- Lexus: How to Replace Your Headlights and Fog Lights
Step by step instructions for do-it-yourself repairs
Browse all: Lexus IS Lighting Guides
HID bulbs for fog lights
#61
Kenny,
You might want to check the wiring harness between the HID bulb and extender. I noticed on mine that depending on which way you insert the connector it can either lock in place or have some freedom to move around. I used a cable tie to secure the connectors together.
Good luck
You might want to check the wiring harness between the HID bulb and extender. I noticed on mine that depending on which way you insert the connector it can either lock in place or have some freedom to move around. I used a cable tie to secure the connectors together.
Good luck
I was able to reconnect and properly secure the ballast on the passenger side fog light. Then I discovered that the driver side fog light wasn't working...no luck fixing it. I'll have to buy another ballast or kit.
#64
#65
Driver School Candidate
Join Date: Oct 2012
Location: California
Posts: 6
Likes: 0
Received 0 Likes
on
0 Posts
Anyone have issues on installing their H11 bulbs? On the factory bulb it shows, H16 but everyone is using H11 bulbs. Is there any modification needed for the install of the bulbs?
#66
I wanted to revive this thread after installing the LEDs. The HIDs are an easier mod. Also, I wanted to again answer some members questions.
1) No, you do not need a relay or fuse. My HIDs went out on me due to improper mounting of the ballast. I left them like that (for over two months) until I installed the LEDs...no problem the LEDs fired right up.
2) Mount the ballast with anything other than the double-sided tape (heavy-duty velcro may be one choice)
3) Be sure to get the polarity right (+) and (-).
I hope this helps.
1) No, you do not need a relay or fuse. My HIDs went out on me due to improper mounting of the ballast. I left them like that (for over two months) until I installed the LEDs...no problem the LEDs fired right up.
2) Mount the ballast with anything other than the double-sided tape (heavy-duty velcro may be one choice)
3) Be sure to get the polarity right (+) and (-).
I hope this helps.
#67
Former Sponsor
iTrader: (11)
Thanks for updating the thread. We always include both double sided tape and tie straps with our HID kits as I agree with you that double sided tape will fail (regardless of the quality).
While they won't provide as much light as an HID kit, our 30W H11 CREE LED bulbs will be pretty bright and are a nice match for HID low beams.
Steve
While they won't provide as much light as an HID kit, our 30W H11 CREE LED bulbs will be pretty bright and are a nice match for HID low beams.
Steve
#68
Driver School Candidate
Join Date: Jan 2013
Location: Fl
Posts: 17
Likes: 0
Received 0 Likes
on
0 Posts
Thanks for updating the thread. We always include both double sided tape and tie straps with our HID kits as I agree with you that double sided tape will fail (regardless of the quality).
While they won't provide as much light as an HID kit, our 30W H11 CREE LED bulbs will be pretty bright and are a nice match for HID low beams.
Steve
While they won't provide as much light as an HID kit, our 30W H11 CREE LED bulbs will be pretty bright and are a nice match for HID low beams.
Steve
#69
I installed this kit tonight and am very pleased. It was a very simple installation and everything fit perfectly. I can confirm that the H11 bulbs fit perfectly. I could not give this product a higher recommendation. I am also very happy with the final result, those awful looking fog lights are a thing of the past!!
#71
Driver School Candidate
Join Date: Jun 2013
Location: Indiana
Posts: 18
Likes: 0
Received 0 Likes
on
0 Posts
http://www.ebay.com/itm/270402461629...S:3160&vxp=mtr
Once ordered, send payment via Paypal and include a note stating you want H11 with 5000k to match the headlights.
Once ordered, send payment via Paypal and include a note stating you want H11 with 5000k to match the headlights.
#72
Driver School Candidate
Join Date: Aug 2013
Location: TX
Posts: 44
Likes: 0
Received 0 Likes
on
0 Posts
Just an update that I installed the H11 HID lights offered by orangemica on eBay. Since they are 5,000 and not 4,300, they do look a bit whiter than the headlights, but are a much, much, much better match than the factory incandescents. They look really sharp and for $28.99 with free shipping, I figured I couldn't go wrong!
I'm not a very technical car guy and was able to do it. I leveraged the info in this thread and it helped greatly. Here are some of my tips:
1. Do the driver's side first. The passenger side will be slightly more challenging since there is a fluid reservoir in front of the fog light. So become a pro at the driver's side, then do the passenger side.
2. I felt I only needed to remove two screws and two clips to get the job done. I removed too much when doing the driver's side. Here is the ones that I did:
-- On the plastic pan on the bottom of the car, you'll notice a rubber shield of some sort right in front of the wheel also bolted to the plastic pan. There are three screws on this rubber shield. I removed the first two closest to the outside of the car.
-- The first two clips starting from the ground from the wheel well. Read in the owner's manual about how to change the signal lights for info on how to remove these. THey are simple though. The first you just turn a screw to remove and the next you use a screwdriver to pop out the top part. The owner's manual has a better description of how to do it.
From there I peeled back the wheel well and had great access to the foglight and surrounding area.
3. The kit comes with a black and red wire with end plugs that you then insert into a plastic connector that will fit into the factory connector. Before inserting them into this plastic connector, I recommend connecting them individually into the factory plug to test the light and understand what orientation the plug ends need to be. When I first did it, I put the red and black wire in the plastic connector. The polarity was right, but I had the plug ends facing the wrong direction. It would still plug into the factory socket, but not work. But once they are in the plastic socket, they are difficult to remove. So test the orientation first, then slide them into the plastic socket, then put the plastic socket into the factory plug.
4. I ended up using the double-sided tape. I'll probably pay for it later, but for now I have instant gratification. I tried some epoxy and stuff, but I couldn't get it to stick. I chose a place where the ballast could rest on the lip of the bumper. I figured it may have support and be cooler there. But I don't know.
Thanks for all of the help guys. Most impactful $29 I've ever spent. I would take pics, but they look the same as the other pics on the thread.
Jacob
I'm not a very technical car guy and was able to do it. I leveraged the info in this thread and it helped greatly. Here are some of my tips:
1. Do the driver's side first. The passenger side will be slightly more challenging since there is a fluid reservoir in front of the fog light. So become a pro at the driver's side, then do the passenger side.
2. I felt I only needed to remove two screws and two clips to get the job done. I removed too much when doing the driver's side. Here is the ones that I did:
-- On the plastic pan on the bottom of the car, you'll notice a rubber shield of some sort right in front of the wheel also bolted to the plastic pan. There are three screws on this rubber shield. I removed the first two closest to the outside of the car.
-- The first two clips starting from the ground from the wheel well. Read in the owner's manual about how to change the signal lights for info on how to remove these. THey are simple though. The first you just turn a screw to remove and the next you use a screwdriver to pop out the top part. The owner's manual has a better description of how to do it.
From there I peeled back the wheel well and had great access to the foglight and surrounding area.
3. The kit comes with a black and red wire with end plugs that you then insert into a plastic connector that will fit into the factory connector. Before inserting them into this plastic connector, I recommend connecting them individually into the factory plug to test the light and understand what orientation the plug ends need to be. When I first did it, I put the red and black wire in the plastic connector. The polarity was right, but I had the plug ends facing the wrong direction. It would still plug into the factory socket, but not work. But once they are in the plastic socket, they are difficult to remove. So test the orientation first, then slide them into the plastic socket, then put the plastic socket into the factory plug.
4. I ended up using the double-sided tape. I'll probably pay for it later, but for now I have instant gratification. I tried some epoxy and stuff, but I couldn't get it to stick. I chose a place where the ballast could rest on the lip of the bumper. I figured it may have support and be cooler there. But I don't know.
Thanks for all of the help guys. Most impactful $29 I've ever spent. I would take pics, but they look the same as the other pics on the thread.
Jacob
#73
Driver School Candidate
Join Date: Jan 2003
Location: Virginia
Posts: 24
Likes: 0
Received 0 Likes
on
0 Posts
HID bulbs for fog lights
Just another .02 cents worth of info.I also ordered and tried the HID kit off Ebay and had some issues as have other members. One side would work well intermittantly and sometimes the other,so I remounted the ballasts and eventually experienced similar results. I removed them and now have the V LED bulbs for about 2 months with no issues. I reasoned that with fewer components there are less chances of failure IMHO.Hope my experience will help someone else here!
#74
Driver School Candidate
Thread Starter
Join Date: Jan 2013
Location: TX
Posts: 33
Likes: 0
Received 0 Likes
on
0 Posts
Just another .02 cents worth of info.I also ordered and tried the HID kit off Ebay and had some issues as have other members. One side would work well intermittantly and sometimes the other,so I remounted the ballasts and eventually experienced similar results. I removed them and now have the V LED bulbs for about 2 months with no issues. I reasoned that with fewer components there are less chances of failure IMHO.Hope my experience will help someone else here!