JLB Motorsports - 19" Staggered / Concave "Apollo Wheels" - Fits GS, IS, LS, SC, ES
02-06-10, 11:35 PM
#62
Lexus Test Driver
Join Date: Sep 2006
Location: Hawaii
Posts: 807
Likes: 0
Received 0 Likes
on
0 Posts
I was able to snap a quick picture finally, even though my car is dirty and it was raining earlier you can't tell so much cuz my car is white. I know its not a straight on shot, but this was just a quick picture, i'll be taking alot more soon once its gets sunny again.
Thanks again guys at JLB
Thanks again guys at JLB
02-07-10, 12:35 AM
#63
Lexus Test Driver
iTrader: (1)
Join Date: Aug 2008
Location: Socal
Posts: 1,272
Likes: 0
Received 0 Likes
on
0 Posts
255/35.
I've got a slight rub only the passenger side and only on bigger dips but its not that bad anymore now that i got my fenders shaved today.
I've got a slight rub only the passenger side and only on bigger dips but its not that bad anymore now that i got my fenders shaved today.
Last edited by xuningshen; 02-28-10 at 01:56 PM.
02-09-10, 02:06 AM
#66
Lexus Test Driver
iTrader: (1)
Join Date: Aug 2008
Location: Socal
Posts: 1,272
Likes: 0
Received 0 Likes
on
0 Posts
if you have an is 350 you have to run a 10mm spacer to clear the brakes, but if you have a 250 you'll be fine w/o it. and as to being flush you need at least a 15mm spacer to be flush up front but then you'll start rubbing unless you go 215/35/19-ish on the tires in the front
if you got the +20 offsets all around and stretched tires you'd be hella flush but you'd have to do fender mods as well
its not like running spacers hurts your car anymore then getting lower offsets. also they're safe as long as you torque em down right
if you got the +20 offsets all around and stretched tires you'd be hella flush but you'd have to do fender mods as well
its not like running spacers hurts your car anymore then getting lower offsets. also they're safe as long as you torque em down right
02-09-10, 02:07 PM
#67
Pole Position
iTrader: (5)
Join Date: Apr 2008
Location: Toronto
Posts: 376
Likes: 0
Received 0 Likes
on
0 Posts
ooic.. hrm.. i may run the small setup.. but i did make it thru with a +30 offset with 235s on the front. so i may just put 10 in the front n back cus these rims come +40. thanks for the input xuningshen, im guessing you rolled your fenders? sigh i guess i got to too.
02-09-10, 03:15 PM
#68
Lexus Test Driver
iTrader: (1)
Join Date: Aug 2008
Location: Socal
Posts: 1,272
Likes: 0
Received 0 Likes
on
0 Posts
the front should be fine, i have no rubbing on 10mm in front and havvn't done anything ot the front fenders, but the rear, w/ spacers i've got +25 offset and i'm rubbing w/ the 255/35 tire so i had to shave my fenders.
np man
np man
02-09-10, 05:49 PM
#70
Former Sponsor
Thread Starter
Join Date: Sep 2009
Location: CA
Posts: 96
Likes: 0
Received 0 Likes
on
0 Posts
Thanks for posting the photos! We have sent PMs to everyone inquiring. I apologize for the 2-day delay in responding to some of you. We had a lot of orders to process over the weekend, and it slowed our forum response time a little bit.
We will be address the brake clearance issue in our future batches. The offset will be decreased to +30mm for the front wheels. We are still offering free 10mm hub centric spacers for use with the +40mm offset wheels. The +30mm offset wheels arrive once we sell out of the current +40mm offset setup.
It should also be noted that the +40mm offset fits perfectly on the IS250, as well as most older Lexus models (SC300/400, GS300/400, etc.).
We will be address the brake clearance issue in our future batches. The offset will be decreased to +30mm for the front wheels. We are still offering free 10mm hub centric spacers for use with the +40mm offset wheels. The +30mm offset wheels arrive once we sell out of the current +40mm offset setup.
It should also be noted that the +40mm offset fits perfectly on the IS250, as well as most older Lexus models (SC300/400, GS300/400, etc.).
02-11-10, 05:22 PM
#72
Former Sponsor
Thread Starter
Join Date: Sep 2009
Location: CA
Posts: 96
Likes: 0
Received 0 Likes
on
0 Posts
We'll probably keep the rear closer to a +35/+40mm offset for those who do not want to roll their fenders, unless we receive some pre-orders for a +30mm in the rear. It's definitely something we will entertain ordering if we have enough demand.
02-11-10, 10:06 PM
#74
Driver
iTrader: (1)
Join Date: Jan 2010
Location: Cali
Posts: 180
Likes: 0
Received 0 Likes
on
0 Posts
Hey guys just got tires put on please check out the link lots of pictures. Thanks again.
https://www.clublexus.com/forums/is-...ew-wheels.html
https://www.clublexus.com/forums/is-...ew-wheels.html
02-12-10, 10:58 PM
#75
Lexus Test Driver
Join Date: Sep 2006
Location: Hawaii
Posts: 807
Likes: 0
Received 0 Likes
on
0 Posts
I'll preorder one set if you make +30 front and back.