Build Threads Details on Club Lexus 2GS owner vehicles

Will's Black GS400 - Going all out now

Thread Tools
 
Search this Thread
 
Old 06-23-21, 03:39 PM
  #91  
lextech89
Driver School Candidate
 
lextech89's Avatar
 
Join Date: Jan 2014
Location: Georgia
Posts: 20
Likes: 0
Received 26 Likes on 9 Posts
Default

hey man did you ever get this thing dynoed again once you had everything installed?
Old 06-24-21, 03:46 PM
  #92  
Will_GS400
Pole Position
Thread Starter
iTrader: (1)
 
Will_GS400's Avatar
 
Join Date: Feb 2012
Location: BC
Posts: 238
Received 41 Likes on 27 Posts
Default

Originally Posted by lextech89
hey man did you ever get this thing dynoed again once you had everything installed?
Not yet, I haven't gotten everything installed. I picked up an extremely rare used RMM supercharger kit. The kit is currently at my local speed shop but they are backed up and haven't had time to book me in yet. As there is next to no documentation on the installation of the kit, it'll take the shop a while to figure things out and fabricate along the way. A few months ago, I had a lower mile 1UZ engine swapped into my car. My car has 250k miles on it and I swapped a 70k mile engine from a local wrecked low mile GS400. The RMM supercharger will do well with the low mile engine. It runs really well and pulls harder than my old engine.

The following 2 users liked this post by Will_GS400:
661SicKGs3 (09-25-22), captainva (09-20-22)
Old 09-09-22, 11:39 AM
  #93  
preemoguru
Rookie
 
preemoguru's Avatar
 
Join Date: Jul 2022
Location: TX
Posts: 29
Likes: 0
Received 2 Likes on 2 Posts
Default

Originally Posted by Will_GS400
Everything is good. I don't track or race it, I daily drive it around the city. The air suspension is great, I can air up and ride at a normal ride height without scraping over speed bumps and driveway entrances but slam it when I park or want to take photos. I had a slight leak on the drive side airline due to me not using enough teflon tape on the threads but I fixed that and the entire system is air tight with no loss in PSI.

One thing I should have done was install height sensors. PSI in the bags don't always correlate to a certain ride height so I could be at 80 PSI per bag and really low or it could be a 2" fender gap and I never know until I get out and look. With height sensors, it doesn't care about PSI and just adjust pressure to to height. I'll be adding that feature later on this year.

I could see air suspension being a gigantic headache if it wasn't installed properly, chasing air leaks and electrical gremlins everywhere but if done right, it'll give you the best of both worlds (looks and performance)

damn this looks good!!
The following users liked this post:
661SicKGs3 (09-25-22)
Old 09-25-22, 11:15 PM
  #94  
661SicKGs3
Rookie
 
661SicKGs3's Avatar
 
Join Date: Mar 2012
Location: CA
Posts: 49
Received 3 Likes on 2 Posts
Default



I never fully committed to the S9 widebody and only went with the rear duckbill trunk. I kinda wished the fenders were weld in but maybe one day I'll spend the money lol. I through it all into the motor lol
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
RyanR317
Lexus Vehicles Classifieds
5
10-28-14 01:52 PM
Bnastyy
Lexus Vehicles Classifieds
3
07-12-12 03:56 PM
TLcoats
Lexus Vehicles Classifieds
23
09-16-10 09:56 AM
LazyAlex
GS - 2nd Gen (1998-2005)
1
06-04-06 10:54 AM
Pr3ttyboi
2Gen GS430 / 400/ 300 Classifieds (98-05)
2
12-02-04 01:11 AM



Quick Reply: Will's Black GS400 - Going all out now



All times are GMT -7. The time now is 10:05 AM.