Technical Help (by Mitsuguy and ArmyofOne)
#92
ok i will wait ..
Also i have made a thread on Es300 forum about the gas/fuel needle acting weird in that i have noticed for few months that the fuel gauge needle sometimes goes down a little bit and than comes back to the original reading..its only a minor drop but can be noticeable. And it usually happen when driving. and it doesn't matter what grades/octane of fuel i use.
Also i have made a thread on Es300 forum about the gas/fuel needle acting weird in that i have noticed for few months that the fuel gauge needle sometimes goes down a little bit and than comes back to the original reading..its only a minor drop but can be noticeable. And it usually happen when driving. and it doesn't matter what grades/octane of fuel i use.
#93
Maintenance Moderator
iTrader: (2)
ok i will wait ..
Also i have made a thread on Es300 forum about the gas/fuel needle acting weird in that i have noticed for few months that the fuel gauge needle sometimes goes down a little bit and than comes back to the original reading..its only a minor drop but can be noticeable. And it usually happen when driving. and it doesn't matter what grades/octane of fuel i use.
Also i have made a thread on Es300 forum about the gas/fuel needle acting weird in that i have noticed for few months that the fuel gauge needle sometimes goes down a little bit and than comes back to the original reading..its only a minor drop but can be noticeable. And it usually happen when driving. and it doesn't matter what grades/octane of fuel i use.
#96
Driver School Candidate
Join Date: Sep 2011
Location: PA
Posts: 6
Likes: 0
Received 0 Likes
on
0 Posts
Noise break peddle
Every time I take my foot oft the break it makes this noise like somthing is worn out...sounds like I am driving a truck...any idea on how to fix it?
#98
Maintenance Moderator
iTrader: (2)
essentially:
pull petcock at bottom of radiator, allow as much to come out as possible
fill with water, drain again
fill with water and flush chemical
start engine, allow to heat up completely, turn heater on high 10 minutes or more
allow to cool
drain again
fill with water, drain again
(here's an additional step I do)
fill with water, start engine, allow to heat up completely, heater on high 10 minutes
allow to cool
drain again
fill with water, drain again
fill with coolant - because some water remains in the block, I use full strength coolant, 1 gallon, then 1/2 gallon water (supposed to be distilled, but IMO, it doesn't matter - it becomes normal water the second it hits the cooing system anyways), then top off as needed... your goal on a hydrometer is to go for -32 degrees F, which is essentially 50/50 coolant / antifreeze...
Personally, I use standard Green coolant, with all the additives (and just change every 2 years), but there is a newer coolant out there that is even better called Khameleon that we are going to start carrying at work... works with almost any system and is long life as well...
#99
is radiator flush and coolant flush same or different things? because my Lexus service person told me its time for coolant flush..so does it mean that the radiator will be flushed too or just coolant? ..and if its just coolant then should i go ahead with radiator flush too ? my car is 2000 es300 with 101,000miles on it...thanks
#101
Maintenance Moderator
iTrader: (2)
is radiator flush and coolant flush same or different things? because my Lexus service person told me its time for coolant flush..so does it mean that the radiator will be flushed too or just coolant? ..and if its just coolant then should i go ahead with radiator flush too ? my car is 2000 es300 with 101,000miles on it...thanks
#102
Just purchased a 2012 RX AWD, NAV, Comfort Pkg, Premium Pkg. I traded in a 2004 RX AWD fully loaded with 64K and never had any problems. I'm not sure about purchasing an extended warranty because by buying the 7 year/70k mileage plan for $1695 I would be paying for 4 years that my factory warranty already covers. If the plan picked up at the end of my factory warranty I could understand. I realize there are alot more mechanical things that could go wrong which is why I'm concerned. Any advice?
#103
so ok i got my coolant changed from Lexus service how can i tell the before and after fluid..because before i could see some particles and now i still see pretty much same thing,,and also the colour of the fluid ( i think) looks the same to me...is there any way i can tell before from after of the coolant ..thanks
#104
Driver School Candidate
Join Date: Oct 2011
Location: OR
Posts: 1
Likes: 0
Received 0 Likes
on
0 Posts
Side moulding
Hey! I was wondering if you could help me out. I'm trying to install the window side moulding because it got damaged when the guy tinting my car was using a heat gun. It's the window moulding that's literally in between the 2 windows on each side that's about a 1-2 inches thick. I've tried looking everywhere, so if you could help. I'd be very greatful.
Ps it's part 75761a
Ps it's part 75761a
#105
Driver School Candidate
iTrader: (1)
Join Date: May 2011
Location: 3727
Posts: 30
Likes: 0
Received 0 Likes
on
0 Posts
i have a sub in my car that i put in. but i dont have a remote turn on line. i do but for some reason it stays at 12v after i put everything back togther. before i used a multi meter to test the wire and it would show 0. i am guesing it because my postive lead and rto are too close. and so what im asking is there another wire i can tap into from the factory amp. btw i have a 2008 lexus gs350 awd w/ navi but w/o mark levinson.