IS - 1st Gen (2001-2005) Discussion about the IS models up to the 2005 model

Throttle Issue!

Thread Tools
 
Search this Thread
 
Old 08-28-12, 03:06 PM
  #1  
ais300c
Pole Position
Thread Starter
 
ais300c's Avatar
 
Join Date: Sep 2010
Location: fl
Posts: 398
Likes: 0
Received 0 Likes on 0 Posts
Default Throttle Issue!

So I have an 03 is300 and I love it. I have about 106,000 miles on it and have had minor issues, until now. Yesterday i was driving and I would accelerate but the car wouldnt move then it would rev and bogg over and over. after about a mile the cel came on and the car wouldnt move unless i floored the accelerator pedal. I took it to my shop ( had it towed) and hooked up my solus. as I depressed the accelerator the computer was only reading 20% throttle almost all the way depressed. had code 2121 which is throttle position sensor. FYI it wasnt the TPS it is what is called the "Throttle control motor" I had this issue and thought I would post so if anyone comes up with this issue they have something to refer to. I will post pics of what it is and what I replaced tomorrow when the part comes in from stupid Lexus of Tampa. I hope this helps someone, if not at least I did my CL duties lol.
Old 08-28-12, 03:20 PM
  #2  
mitsuguy
Maintenance Moderator

iTrader: (2)
 
mitsuguy's Avatar
 
Join Date: May 2005
Location: AZ
Posts: 6,388
Likes: 0
Received 24 Likes on 21 Posts
Default

bad throttle motor... going to need a new/used throttle body...

the 20% throttle you are able to get is kinda of a manual drive wire limp mode - when the throttle motor stops working, it still gives you 20% of throttle ability, and its the last 20% of pedal throw...
Old 08-29-12, 05:27 AM
  #3  
ais300c
Pole Position
Thread Starter
 
ais300c's Avatar
 
Join Date: Sep 2010
Location: fl
Posts: 398
Likes: 0
Received 0 Likes on 0 Posts
Default

I just ordered a new motor, You sure Im gonna need the whole throttle body man?
Old 08-29-12, 07:03 AM
  #4  
mitsuguy
Maintenance Moderator

iTrader: (2)
 
mitsuguy's Avatar
 
Join Date: May 2005
Location: AZ
Posts: 6,388
Likes: 0
Received 24 Likes on 21 Posts
Default

Originally Posted by ais300c
I just ordered a new motor, You sure Im gonna need the whole throttle body man?
That's kinda what I meant... usually you can find the whole used assembly quite a bit cheaper than just a new motor...

I've also heard of some weird calibration issues when just replacing the motor, but, to my knowledge, that can be fixed with some trial and error...
Old 08-29-12, 12:18 PM
  #5  
ais300c
Pole Position
Thread Starter
 
ais300c's Avatar
 
Join Date: Sep 2010
Location: fl
Posts: 398
Likes: 0
Received 0 Likes on 0 Posts
Default

Well I ordered a new motor so I'll know today if it works, it's easier and faster to get the motor since this is my dd walking to work sucks but yea I read up on calibration that's too hard but I will know if it fixes it and plus didn't want to go used and have this same problem in a few months that was the only reason I didn't get a whole used throttle body it wasn't that much more
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
LexIS03300
IS - 1st Gen (2001-2005)
1
02-27-18 10:27 PM
Cp2295
LS - 1st and 2nd Gen (1990-2000)
4
11-26-16 12:24 AM
4blizak4mn
SC430 - 2nd Gen (2001-2010)
35
02-09-15 08:33 AM
drewster12
IS - 2nd Gen (2006-2013)
1
08-30-13 10:55 AM
BigDave
GS - 2nd Gen (1998-2005)
1
04-01-05 02:34 AM



Quick Reply: Throttle Issue!



All times are GMT -7. The time now is 01:27 AM.