ClubLexus - Lexus Forum Discussion
They really enjoy the rear zone A/C
They really enjoy the rear zone A/C
0 2021/03/31 12:29:51
0 2021/03/28 17:54:19
0 2021/03/28 17:51:04
After a test (road trip while towing) had to adjust some tubes
After a test (road trip while towing) had to adjust some tubes
0 2021/03/28 17:48:55
0 2021/03/28 17:47:53
0 2021/03/28 17:47:02
0 2021/03/28 17:41:40
Wanted to test air system before I bolted everything on. Burtn a hose and needed to re route some runs to avoid any heat
Wanted to test air system before I bolted everything on. Burtn a hose and needed to re route some runs to avoid any heat
0 2021/03/28 17:39:02
0 2021/03/28 17:37:12
Zoomed in view of EZ lift
Zoomed in view of EZ lift
0 2021/03/26 09:08:12
0 2021/03/26 09:05:46
Add rubber vacuum covers to all the quick connects
Add rubber vacuum covers to all the quick connects
0 2021/03/23 22:40:55
0 2021/03/23 22:39:01
0 2021/03/23 22:38:27
No assistant so used a piece of wood and the car jack to raise it in place provided bolts were not quite right but was able to get secured feels solid hope the A arms fit
No assistant so used a piece of wood and the car jack to raise it in place provided bolts were not quite right but was able to get secured feels solid hope the A arms fit
0 2021/03/23 22:29:40
Totally legit engineering diagram of set up (gray = tires blue = air tubes, yellow = 3/8 OD brass barbs purple 1/4 npt male quick connects, gold 3 way female manifolds, green PSI gauge and red is release value )
Totally legit engineering diagram of set up (gray = tires blue = air tubes, yellow = 3/8 OD brass barbs purple 1/4 npt male quick connects, gold 3 way female manifolds, green PSI gauge and red is release value )
0 2021/03/22 22:26:36
0 2021/03/22 22:13:12
The 4 quick connects in bag with compressor
The 4 quick connects in bag with compressor
0 2021/03/22 22:13:10
While tightening and I checked for loose connection with tire pressure
While tightening and I checked for loose connection with tire pressure
0 2021/03/22 22:13:07
0 2021/03/22 22:09:51
0 2021/03/22 22:08:01
0 2021/03/21 23:04:06
0 2021/03/21 23:01:02
Used fender washer to secure with preexisting holes
Used fender washer to secure with preexisting holes
0 2021/03/21 22:57:57
0 2021/03/21 22:57:46
Quick connect which if I switch to in board air will become my pressure release
Quick connect which if I switch to in board air will become my pressure release
0 2021/03/21 22:54:24
0 2021/03/21 22:54:16
0 2021/03/21 22:52:49
Hope this can. Help Poor lighting and at night. I ended up cutting those off with my grinder so it would fit with cbi half bumper
Hope this can. Help Poor lighting and at night. I ended up cutting those off with my grinder so it would fit with cbi half bumper
0 2021/02/24 18:48:22
just some before and after pics
just some before and after pics
0 2021/02/21 22:43:57
0 2021/02/21 22:43:42
Just a better photo of the factory AWM option. Works well form me has collected a few dog barfing incidents
Just a better photo of the factory AWM option. Works well form me has collected a few dog barfing incidents
0 2021/02/20 15:08:51
0 2021/02/20 15:08:46
Passenger side hole access the winch wiring in case of troubles Driver side is a must for free spilling the winch line
Passenger side hole access the winch wiring in case of troubles Driver side is a must for free spilling the winch line
0 2021/02/20 09:27:27
3300 lbs and getting about 11 mpg on 33s with trailer
3300 lbs and getting about 11 mpg on 33s with trailer
0 2021/02/13 17:35:32
No issues with power or braking
No issues with power or braking
0 2021/02/13 17:34:32
Terrible picture but you can see the AWM (with junk on it) sitting between
Terrible picture but you can see the AWM (with junk on it) sitting between
0 2021/02/07 11:09:50
Closed nicely, but not sure how much I'll used besides for charging.
Closed nicely, but not sure how much I'll used besides for charging.
0 2021/01/24 19:36:47
I already sacrificed the 12v for rear usb and used the space as USB pass through
I already sacrificed the 12v for rear usb and used the space as USB pass through
0 2021/01/24 19:36:42
used only one bracket secured back side with 3m tape, used spade bit to make hole in removable plastic for wire pass through
used only one bracket secured back side with 3m tape, used spade bit to make hole in removable plastic for wire pass through
0 2021/01/24 19:36:35