ClubLexus - Lexus Forum Discussion
0 2015/08/14 15:02:34
0 2015/08/13 17:16:32
0 2015/08/08 17:23:12
0 2015/08/06 05:10:20
0 2015/08/06 05:09:50
Falcon 360HD
Falcon 360HD
0 2015/08/05 18:13:55
If you look on the top left of the box you will see a ground? Well I couldn't get a reading with my volt meter so I went to the body.
If you look on the top left of the box you will see a ground? Well I couldn't get a reading with my volt meter so I went to the body.
0 2015/08/04 14:25:22
Left is the Lexus fuse and right is a standard mini. The Lexus fuse will not fit in the Add-A-Circuit. You may notice I am using a 7.5 and the circuit calls for a 15, I didn't know the fuse size problem and haven't gotten around to picking up a 15. I used a 3 volt for my camera with no problems so far.
Left is the Lexus fuse and right is a standard mini. The Lexus fuse will not fit in the Add-A-Circuit. You may notice I am using a 7.5 and the circuit calls for a 15, I didn't know the fuse size problem and haven't gotten around to picking up a 15. I used a 3 volt for my camera with no problems so far.
0 2015/08/04 14:25:20
I used the WIP RR, this is switched and gave me some room to lay the parts in the Fusebox. I drilled a small hole in the back top of the box to run the wire through.
I used the WIP RR, this is switched and gave me some room to lay the parts in the Fusebox. I drilled a small hole in the back top of the box to run the wire through.
0 2015/08/04 14:25:18
I took apart a typical auxiliary to USB adapter and soldered it to the Add-A-Circuit. I wrapped it with heat shrink, but it didn't really form well with the different sizes. You may want to use electrical tape.
I took apart a typical auxiliary to USB adapter and soldered it to the Add-A-Circuit. I wrapped it with heat shrink, but it didn't really form well with the different sizes. You may want to use electrical tape.
0 2015/08/04 14:25:15
0 2015/08/04 14:25:13
I had a separate little rubber nipple that wasn't used ( it may be used for something on yours) I cut the tip off and ran a Glo-Rod through it.
I had a separate little rubber nipple that wasn't used ( it may be used for something on yours) I cut the tip off and ran a Glo-Rod through it.
0 2015/08/04 14:25:10
Remove the 2 screws on the pillar handle and pull the cover up and out. There is plenty of room to put the wire on the back side of the airbag.
Remove the 2 screws on the pillar handle and pull the cover up and out. There is plenty of room to put the wire on the back side of the airbag.
0 2015/08/04 14:25:07
0 2015/08/03 07:10:33
0 2015/08/03 07:10:22
0 2015/08/02 14:16:18
0 2015/08/02 14:16:15
0 2015/08/02 14:16:13
0 2015/08/02 14:16:11
0 2015/07/31 14:45:11
0 2015/07/31 14:45:09
0 2015/07/31 13:32:33
0 2015/07/29 09:24:02
0 2015/07/29 09:21:57
0 2015/07/28 16:56:33
0 2015/07/27 17:38:38
0 2015/07/27 17:38:36
0 2015/07/27 17:38:32
0 2015/07/27 17:38:31
0 2015/07/27 17:38:29
0 2015/07/27 17:38:27
0 2015/07/27 17:38:22
0 2015/07/27 17:38:14
0 2015/07/24 17:49:15
0 2015/07/24 17:49:13
Max settings
Max settings
0 2015/07/22 16:23:46
Default settings.
Default settings.
0 2015/07/22 16:23:43
0 2015/07/22 16:21:58
[quote] When the vehicle is on the guidance route, the distance measured along the route is displayed. Travel time and arrival time are calculated based on the average speed for the specified speed limit.[/quote].
[quote] When the vehicle is on the guidance route, the distance measured along the route is displayed. Travel time and arrival time are calculated based on the average speed for the specified speed limit.[/quote].
0 2015/07/22 15:28:26
0 2015/07/10 13:38:31