ClubLexus - Lexus Forum Discussion
0 2017/10/14 23:16:26
0 2017/10/14 23:17:07
0 2017/10/14 23:17:39
0 2017/10/14 23:18:30
LED DRL
LED DRL
0 2017/10/14 23:19:02
HID Projector Fog
HID Projector Fog
0 2017/10/14 23:19:53
Projector Fog Cutoff
Projector Fog Cutoff
0 2017/10/14 23:20:53
0 2017/10/14 23:40:42
0 2017/10/14 23:56:38
0 2017/10/14 23:58:35
0 2017/10/15 05:24:24
0 2017/10/15 05:25:14
0 2017/10/15 05:26:22
Oem 9006 fog wire plugs right into ballast then harness goes right back to housing.
Oem 9006 fog wire plugs right into ballast then harness goes right back to housing.
0 2017/10/15 05:27:06
i tested everything before install. This is LED DRL portion.
i tested everything before install. This is LED DRL portion.
0 2017/10/15 05:27:48
Testing HID portion
Testing HID portion
0 2017/10/15 05:35:28
Projectors are very bright but sharp cutoff. I have not been flashed yet by oncoming drivers because these projectors put the light exactly where needed and meant to handle Xenon light
Projectors are very bright but sharp cutoff. I have not been flashed yet by oncoming drivers because these projectors put the light exactly where needed and meant to handle Xenon light
0 2017/10/15 05:36:26
Made my own harness for the LEDs using the skinny slide on wire terminals.
Made my own harness for the LEDs using the skinny slide on wire terminals.
0 2017/10/15 05:39:23
These work perfectly since the harness plug is so narrow..but these dont come close to each other when both are on the pos/neg posts inside plug
These work perfectly since the harness plug is so narrow..but these dont come close to each other when both are on the pos/neg posts inside plug
0 2017/10/15 05:40:46
Added the second terminal and wire then added wire loom and wrapped it OG triple triple tight and used 9006 harness pigtail for the other end to make it look a little more professional
Added the second terminal and wire then added wire loom and wrapped it OG triple triple tight and used 9006 harness pigtail for the other end to make it look a little more professional
0 2017/10/15 05:42:41
I had them mounted as they installed my body kit. My painter said they bolted right up to existing mount points but we could not figure out the ballast brackets so we secured those a different way and didnt use them
I had them mounted as they installed my body kit. My painter said they bolted right up to existing mount points but we could not figure out the ballast brackets so we secured those a different way and didnt use them
0 2017/10/15 05:45:28
0 2018/07/31 14:46:41
0 2018/07/31 14:46:43
0 2018/10/01 15:11:16
0 2018/10/01 15:12:25
0 2018/10/01 15:13:29
0 2018/10/01 15:14:16
0 2018/10/01 15:14:56
0 2018/10/02 10:00:41
0 2018/10/02 10:01:42
0 2018/10/02 10:02:49
0 2018/10/02 10:04:20
0 2019/01/04 16:51:00
0 2019/01/04 16:51:00
0 2019/01/04 16:51:00
0 2019/01/04 16:51:00
0 2019/01/04 16:51:00
0 2019/01/04 16:51:00
0 2019/01/04 16:51:01
0 2019/01/04 16:51:01