ClubLexus - Lexus Forum Discussion
Then to install the guide pin. You have to snake it in through the slave hole and then through the hole in the alteration kit; then with loctite on the bolt you have to stretch out the unit fully again (without outer bolts tight). This will allow you to be able to thread it in.
Then to install the guide pin. You have to snake it in through the slave hole and then through the hole in the alteration kit; then with loctite on the bolt you have to stretch out the unit fully again (without outer bolts tight). This will allow you to be able to thread it in.
0 2023/07/14 06:53:02
Lastly with the guide rod tightened down snug with a 17mm wrench; i loctited the outer bolts and torqued them to 27 ft lbs.
Lastly with the guide rod tightened down snug with a 17mm wrench; i loctited the outer bolts and torqued them to 27 ft lbs.
0 2023/07/14 06:53:05
Finished!
Finished!
0 2023/07/14 06:53:07
0 2023/07/14 06:53:10
0 2023/07/14 06:53:12
0 2023/07/15 06:10:46
0 2023/07/15 06:10:49
0 2023/07/15 06:10:52
0 2023/07/15 06:10:55
0 2023/07/15 06:11:01
0 2023/07/15 06:11:03
0 2023/07/15 06:11:08
0 2023/07/15 06:11:11
0 2023/07/15 06:11:14
0 2023/07/15 06:11:16
Driftmotion double lock-down cam sensor seal kit
Driftmotion double lock-down cam sensor seal kit
0 2023/07/16 05:09:00
new sensor showing new o-ring design they come with.
new sensor showing new o-ring design they come with.
0 2023/07/16 05:09:05
double o-ring will definitely not work.
double o-ring will definitely not work.
0 2023/07/16 05:09:10
0 2023/07/16 05:09:13
Removed OEM o-ring
Removed OEM o-ring
0 2023/07/16 05:09:16
0 2023/07/16 06:26:41
0 2023/07/18 03:10:58
0 2023/07/18 03:11:03
0 2023/07/18 03:11:04
Fits pretty well under my regulator. Couldn't run it above because my fuel sensor will be there.
Fits pretty well under my regulator. Couldn't run it above because my fuel sensor will be there.
0 2023/07/20 04:41:23
Ended up having an OEM version of this hose laying around, i think its discontinued now but fits perfect just need clamps.
Ended up having an OEM version of this hose laying around, i think its discontinued now but fits perfect just need clamps.
0 2023/07/20 04:41:26
5/16" gates safety stripe heater hose going to the non vvt-i 2jzgte idle air control valve, the other hose goes between the manifold to the front of the throttle body
5/16" gates safety stripe heater hose going to the non vvt-i 2jzgte idle air control valve, the other hose goes between the manifold to the front of the throttle body
0 2023/07/20 04:41:28
0 2023/07/26 23:02:03
0 2023/07/26 23:02:07
0 2023/07/26 23:16:49
0 2023/07/27 10:19:46
0 2023/07/27 10:19:51
0 2023/07/27 10:19:54
0 2023/07/27 10:19:57
0 2023/07/27 10:20:01
0 2023/07/27 10:20:04
0 2023/07/27 10:20:07
0 2023/07/27 10:21:19
0 2023/07/28 03:49:34
my Ah-HA moment finally getting the input shaft to slide fully into the pilot bearing
my Ah-HA moment finally getting the input shaft to slide fully into the pilot bearing
0 2023/07/30 01:46:25