ClubLexus - Lexus Forum Discussion
Then to install the guide pin. You have to snake it in through the slave hole and then through the hole in the alteration kit; then with loctite on the bolt you have to stretch out the unit fully again (without outer bolts tight). This will allow you to be able to thread it in.
Then to install the guide pin. You have to snake it in through the slave hole and then through the hole in the alteration kit; then with loctite on the bolt you have to stretch out the unit fully again (without outer bolts tight). This will allow you to be able to thread it in.
0 2023/07/14 06:53:02
Snap ring installed while everything was still loose. Added a thin film of grease to this rod as well.
Snap ring installed while everything was still loose. Added a thin film of grease to this rod as well.
0 2023/07/14 06:53:00
0 2023/07/14 06:52:57
0 2023/07/14 06:52:54
Next step is to put it on the input shaft and get the clutch fork aligned to put the pin through it. Then you need to extend open the unit, or remover a spring to slide the pin through the bottom and install a snap ring shown in the next photo.
Next step is to put it on the input shaft and get the clutch fork aligned to put the pin through it. Then you need to extend open the unit, or remover a spring to slide the pin through the bottom and install a snap ring shown in the next photo.
0 2023/07/14 06:52:51
All moving parts here were lubricated, this is essentially how it comes aside from the t-bracket being disassembled.
All moving parts here were lubricated, this is essentially how it comes aside from the t-bracket being disassembled.
0 2023/07/14 06:52:46
used red timken axle grease to all moving parts; i only did a thin layer on everything because you don't want it to fling off.
used red timken axle grease to all moving parts; i only did a thin layer on everything because you don't want it to fling off.
0 2023/07/14 06:52:44
First I installed the t-bracket; this piece is off-set and can only be installed one way. These were blue loctited and torqued to 27 ft lbs.
First I installed the t-bracket; this piece is off-set and can only be installed one way. These were blue loctited and torqued to 27 ft lbs.
0 2023/07/14 06:52:38
0 2023/06/12 22:19:43
0 2023/06/12 22:19:21
0 2023/06/12 22:12:56
0 2023/05/27 03:31:41
0 2023/05/27 03:31:34
0 2023/05/27 03:31:28
0 2023/05/27 03:31:21
0 2023/05/27 03:31:13
0 2023/05/27 03:31:07
0 2023/05/27 03:31:00
0 2023/05/27 03:30:51
0 2023/05/27 03:30:39
0 2023/04/14 01:52:36
0 2023/04/14 01:52:14
0 2023/04/14 01:52:11
0 2023/04/14 01:52:08
0 2023/04/14 01:52:06
0 2023/04/14 01:52:04
0 2023/04/14 01:52:00
0 2023/03/30 22:53:35
0 2023/03/30 22:53:33
0 2023/03/30 22:53:28
0 2023/03/30 22:53:25
0 2023/03/30 22:53:23
0 2023/03/30 22:53:19
0 2022/10/13 01:40:42
0 2022/10/13 01:40:40
0 2022/10/13 01:40:36
0 2022/10/13 01:40:33
0 2022/10/13 01:40:31
0 2022/10/13 01:40:26
0 2022/09/29 00:28:50