ClubLexus - Lexus Forum Discussion
0 2021/02/21 22:43:42
just some before and after pics
just some before and after pics
0 2021/02/21 22:43:57
Hope this can. Help Poor lighting and at night. I ended up cutting those off with my grinder so it would fit with cbi half bumper
Hope this can. Help Poor lighting and at night. I ended up cutting those off with my grinder so it would fit with cbi half bumper
0 2021/02/24 18:48:22
0 2021/03/21 22:52:49
0 2021/03/21 22:54:16
Quick connect which if I switch to in board air will become my pressure release
Quick connect which if I switch to in board air will become my pressure release
0 2021/03/21 22:54:24
0 2021/03/21 22:57:46
Used fender washer to secure with preexisting holes
Used fender washer to secure with preexisting holes
0 2021/03/21 22:57:57
0 2021/03/21 23:01:02
0 2021/03/21 23:04:06
0 2021/03/22 22:08:01
0 2021/03/22 22:09:51
While tightening and I checked for loose connection with tire pressure
While tightening and I checked for loose connection with tire pressure
0 2021/03/22 22:13:07
The 4 quick connects in bag with compressor
The 4 quick connects in bag with compressor
0 2021/03/22 22:13:10
0 2021/03/22 22:13:12
Totally legit engineering diagram of set up (gray = tires blue = air tubes, yellow = 3/8 OD brass barbs purple 1/4 npt male quick connects, gold 3 way female manifolds, green PSI gauge and red is release value )
Totally legit engineering diagram of set up (gray = tires blue = air tubes, yellow = 3/8 OD brass barbs purple 1/4 npt male quick connects, gold 3 way female manifolds, green PSI gauge and red is release value )
0 2021/03/22 22:26:36
No assistant so used a piece of wood and the car jack to raise it in place provided bolts were not quite right but was able to get secured feels solid hope the A arms fit
No assistant so used a piece of wood and the car jack to raise it in place provided bolts were not quite right but was able to get secured feels solid hope the A arms fit
0 2021/03/23 22:29:40
0 2021/03/23 22:38:27
0 2021/03/23 22:39:01
Add rubber vacuum covers to all the quick connects
Add rubber vacuum covers to all the quick connects
0 2021/03/23 22:40:55
0 2021/03/26 09:05:46
Zoomed in view of EZ lift
Zoomed in view of EZ lift
0 2021/03/26 09:08:12
0 2021/03/28 17:37:12
Wanted to test air system before I bolted everything on. Burtn a hose and needed to re route some runs to avoid any heat
Wanted to test air system before I bolted everything on. Burtn a hose and needed to re route some runs to avoid any heat
0 2021/03/28 17:39:02
0 2021/03/28 17:41:40
0 2021/03/28 17:47:02
0 2021/03/28 17:47:53
After a test (road trip while towing) had to adjust some tubes
After a test (road trip while towing) had to adjust some tubes
0 2021/03/28 17:48:55
0 2021/03/28 17:51:04
0 2021/03/28 17:54:19
They really enjoy the rear zone A/C
They really enjoy the rear zone A/C
0 2021/03/31 12:29:51
Side note I'm halfway through the airbag install should get the other one in tonight ran out of daylight
Side note I'm halfway through the airbag install should get the other one in tonight ran out of daylight
0 2021/03/31 12:30:38
Better picture of the WDH. It came with my trailer so I don't know life without it.
Better picture of the WDH. It came with my trailer so I don't know life without it.
0 2021/03/31 12:33:04
0 2021/03/31 20:10:22
0 2021/03/31 20:10:50
Getting the tubing through the existing hole in the top of the spring was trail and error but eventually found its way.
Getting the tubing through the existing hole in the top of the spring was trail and error but eventually found its way.
0 2021/03/31 20:11:16
Inflation point
Inflation point
0 2021/03/31 20:12:22
0 2021/03/31 20:12:43
Plenty of videos online but simply jack up one side at a time run Air tubing and aejust bump stocks with long razer knife and use soapy waters to squeeze airbag in place.
Plenty of videos online but simply jack up one side at a time run Air tubing and aejust bump stocks with long razer knife and use soapy waters to squeeze airbag in place.
0 2021/03/31 20:12:56
0 2021/03/31 20:46:40