Notices
SC - 1st Gen (1992-2000)

1jz code 14 out of no where...ideas pls.

Thread Tools
 
Search this Thread
 
Old Apr 24, 2011 | 05:19 PM
  #1  
evileagle's Avatar
evileagle
Thread Starter
Lexus Test Driver
 
Joined: Aug 2007
Posts: 927
Likes: 3
From: Ca
Default 1jz code 14 out of no where...ideas pls.

So my car has been rock solid for about a year and a half now, then out of no where, the check engine came on for about 3 seconds while driving and the car began to miss pretty bad, and out of no where the light went away and all was fine for about a week. Then the same thing happened again. This time I went to see what codes it came up with and I got 2 codes: 14 and 34. Code 14 says ignition signal and code 34 I couldn't find. Any ideas what this could be? Bad coil? Bad ignitor? All input greatly appreciated. This is my daily so I'd like to get it up and running asap.

Thx!
Reply
Old Apr 24, 2011 | 05:34 PM
  #2  
soarer93's Avatar
soarer93
Pole Position
 
Joined: Apr 2011
Posts: 277
Likes: 0
From: Manitoba
Default

From the workshop manual - it says

-Abnormal Turbocharger pressure

Code 34; usually happens when you are hitting boost cut.

Last edited by soarer93; Apr 24, 2011 at 05:39 PM. Reason: more info to add
Reply
Old Apr 24, 2011 | 06:06 PM
  #3  
evileagle's Avatar
evileagle
Thread Starter
Lexus Test Driver
 
Joined: Aug 2007
Posts: 927
Likes: 3
From: Ca
Default

Right now when I start the car at idle, it misses like its on 5 cylinders or something... It sounds like a scooby ......

This has to do with the ignition system, I just don't know where. Would a bad ecu be possible? Like I said, car was running like a clock and then this came out of no where...
Reply
Old Apr 24, 2011 | 07:28 PM
  #4  
RyanV's Avatar
RyanV
Lexus Test Driver
iTrader: (9)
 
Joined: Jan 2008
Posts: 1,311
Likes: 3
From: Texas
Default

code 14 igniter signal to ecu missing - Ignition signal (no "igf" signal to ecu, no signal from igniter 4 times in a row

Seems that if this started all of the sudden maybe the igniter went bad or the IGF pin in the igniter is burnt up.

You could also check the resistance of the IGF wire from the igniter all the way to the ECU to see what it look's like.

If it started all of the sudden you'd think the wiring was ok and a hard part went bad(igniter)
Reply
Old Apr 25, 2011 | 08:18 AM
  #5  
evileagle's Avatar
evileagle
Thread Starter
Lexus Test Driver
 
Joined: Aug 2007
Posts: 927
Likes: 3
From: Ca
Default

Originally Posted by RyanV
code 14 igniter signal to ecu missing - Ignition signal (no "igf" signal to ecu, no signal from igniter 4 times in a row

Seems that if this started all of the sudden maybe the igniter went bad or the IGF pin in the igniter is burnt up.

You could also check the resistance of the IGF wire from the igniter all the way to the ECU to see what it look's like.




If it started all of the sudden you'd think the wiring was ok and a hard part went bad(igniter)
Do u know which wire is the igf wire? Im just going to do what you said and see if there's a break anywhere in the system first. If not, it's time to order a new ignitor!
Reply
Old Apr 25, 2011 | 09:07 AM
  #6  
99SC42's Avatar
99SC42
Lexus Test Driver
iTrader: (44)
 
Joined: Jan 2007
Posts: 5,139
Likes: 8
From: Maryland /Germantown
Default

I don't think it's the Ignitor it's the iGF wire like Ryan said the wire is either broken or not making a good contact.
I don't know what color it is on the 1jz but Red with yellow on the 2jzge and gte and pin 58b on the 2jz.
http://www.supraforums.com/forum/sho...nd-coil-wiring
Reply
Old Apr 26, 2011 | 10:20 AM
  #7  
evileagle's Avatar
evileagle
Thread Starter
Lexus Test Driver
 
Joined: Aug 2007
Posts: 927
Likes: 3
From: Ca
Default

what makes this so annoying is that its so random...I started her up and drove around for an hour or so with no problems. I checked continuity from the IGF wire next to the coil down to the ecu, no problem. I took a look at all the coils and wires, they are all good since i replaced all the pigtails when i did the swap over a year ago.

I ended up taking out the ecu, opening it up and looked for some leaking caps. It looked pretty cherry inside but i sent it out to driftmotion to replace the caps for me. Hopefully that will be my issue...
Reply
Old Apr 26, 2011 | 10:23 AM
  #8  
evileagle's Avatar
evileagle
Thread Starter
Lexus Test Driver
 
Joined: Aug 2007
Posts: 927
Likes: 3
From: Ca
Default

oh heres a link to the service manual that talks specifically about code 14 for future refrence...

http://mkiv.supras.org.nz/articles/engine_2_14.htm


and for reference:


Last edited by evileagle; Apr 26, 2011 at 10:44 AM.
Reply
Old Oct 11, 2011 | 12:44 PM
  #9  
SH_JZZ30's Avatar
SH_JZZ30
Lexus Champion
iTrader: (1)
 
Joined: Jul 2007
Posts: 2,407
Likes: 2
From: Florida
Default

Has this problem been resolved?
Reply
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
dadewi
GS - 1st Gen (1993-1997)
12
Oct 22, 2018 12:45 PM
msweber97
LS - 1st and 2nd Gen (1990-2000)
16
Jul 20, 2014 10:11 AM
WainiacS
RX - 1st Gen (1999-2003)
11
Nov 28, 2011 07:04 AM
CallmeQ
GS - 1st Gen (1993-1997)
2
Sep 26, 2009 12:19 PM
StiCk3
SC - 1st Gen (1992-2000)
4
Apr 26, 2008 05:40 AM




All times are GMT -7. The time now is 02:42 PM.