CA WTB- Driveshaft Sc300 with getrag
#1
WTB- Driveshaft Sc300 with getrag
I know this is very rare but if you have any Driveshaft that is made for the Sc300 with getrag. Please let me know. I would get this done locally but nobody seems to know the exact measurement and i would rather to this project at home.
NOte: Need this for V160tranny to 6Speed Diff.
NOte: Need this for V160tranny to 6Speed Diff.
Last edited by autoboy; 06-02-10 at 03:55 PM.
#2
Pole Position
iTrader: (11)
Join Date: Feb 2004
Location: Maryland
Posts: 360
Likes: 0
Received 0 Likes
on
0 Posts
Check it Out
We are working on the same project, the V160 is several inches shorter than the SC trans. Looks like you will need to use the 1/2 shaft front section from the supra, it's a few inches longer than SC's, and has the correct flange for the V160(not the same as any SC). Than use the rear half from a SC4. We haven't installed everything yet, but from measuring it looks like this will work. We have a SC4 rear driveshaft, $120 shipped.
Let me know
Regards
Bart
Let me know
Regards
Bart
#3
We are working on the same project, the V160 is several inches shorter than the SC trans. Looks like you will need to use the 1/2 shaft front section from the supra, it's a few inches longer than SC's, and has the correct flange for the V160(not the same as any SC). Than use the rear half from a SC4. We haven't installed everything yet, but from measuring it looks like this will work. We have a SC4 rear driveshaft, $120 shipped.
Let me know
Regards
Bart
Let me know
Regards
Bart
Trending Topics
#10
Lexus Test Driver
iTrader: (44)
Join Date: Jan 2007
Location: Maryland /Germantown
Posts: 5,139
Likes: 0
Received 7 Likes
on
7 Posts
You need an Supra front half and 2000 GS3 rear half that what i will using on the swap am working on i have about 7 driveshafts and the only one that seems to works is the Supra front and 2GS3 rear because it the sliding type DS not like the SC300 but same as the SC400 but the SC4 with the Supra front is too short .
If you can wait till sunday i can confirm 100% that it works with no fitment issues let me know.
If you can wait till sunday i can confirm 100% that it works with no fitment issues let me know.
#11
You need an Supra front half and 2000 GS3 rear half that what i will using on the swap am working on i have about 7 driveshafts and the only one that seems to works is the Supra front and 2GS3 rear because it the sliding type DS not like the SC300 but same as the SC400 but the SC4 with the Supra front is too short .
If you can wait till sunday i can confirm 100% that it works with no fitment issues let me know.
If you can wait till sunday i can confirm 100% that it works with no fitment issues let me know.
#12
Pole Position
iTrader: (5)
Here's one of their fs thread on sf if you want to get in contact:
http://www.supraforums.com/forum/sho...d.php?t=588512
Last edited by GZZ-TT; 06-02-10 at 07:03 PM.
#14
Lexus Test Driver
iTrader: (4)
I got my 1 piece made here http://coastdriveline.com/MeasureShaft.htm
They will tell you where to measure from and too... they are really good. They made me a driveshaft to support 800hp at 180mph, rebuild able, 4" steel because I opted out of the aluminum for 600. All new parts. a bit pricey but still working.
They will tell you where to measure from and too... they are really good. They made me a driveshaft to support 800hp at 180mph, rebuild able, 4" steel because I opted out of the aluminum for 600. All new parts. a bit pricey but still working.