Timing belt inspection/replacement - how do I?
#1
Intermediate
Thread Starter
Timing belt inspection/replacement - how do I?
I'm uncertain of the condition of my timing belt in my 92 SC400 with 200,000 Miles (320,000 km I'm Canadian eh). The car is in great shape, rust free and from what I can make out was dealer maintained till at least 125,000 miles (found a work order with just over 125,000 miles on it from 2000). The car may have been dealer maintained right until I picked it up. The water pump does not look new, so if it was done on schedule it was a while ago (not sure what the scheduled change interval is anyway).
I've looked here for answers, but didn't find anything.
https://www.clublexus.com/forums/sc-...tart-here.html
I'm planning a 2500 mile trip soon and am uncomfortable not knowing the condition of this important maintenance item.
Is my engine a non interference engine? In other words, if the belt breaks am I going to put a valve through a piston?
Can I inspect the belt by pulling a valve cover?
Is there a detailed "how to" belt/water pump/tensioner procedure here somewhere that I've missed.
I'm not afraid of doing the job but am pressed for time. At the other end of my trip a friend out in Vancouver has offered his garage, tools, company and beer to get the job done there. Sounds nicer than working in my unheated garage here out east.
I've looked here for answers, but didn't find anything.
https://www.clublexus.com/forums/sc-...tart-here.html
I'm planning a 2500 mile trip soon and am uncomfortable not knowing the condition of this important maintenance item.
Is my engine a non interference engine? In other words, if the belt breaks am I going to put a valve through a piston?
Can I inspect the belt by pulling a valve cover?
Is there a detailed "how to" belt/water pump/tensioner procedure here somewhere that I've missed.
I'm not afraid of doing the job but am pressed for time. At the other end of my trip a friend out in Vancouver has offered his garage, tools, company and beer to get the job done there. Sounds nicer than working in my unheated garage here out east.
Last edited by Returd; 02-17-17 at 07:34 AM.
#2
Lead Lap
iTrader: (8)
Non-VVTi (pre-'97) 1UZ engines are non-interference. (Edit: Meant pre-'98. '97 and older.)
You can see the timing belt by removing one of the spark plug covers. The driver's side cover is the easier one to quickly pop off.
http://www.lexls.com/tutorials/engine/timingbelt.html
You can see the timing belt by removing one of the spark plug covers. The driver's side cover is the easier one to quickly pop off.
http://www.lexls.com/tutorials/engine/timingbelt.html
Last edited by t2d2; 02-19-17 at 09:33 AM.
The following users liked this post:
Returd (02-18-17)
#4
Driver
iTrader: (3)
http://www.lextreme.com/timing2.html
Aisin made the oem water pump And the oem belt makes lining up timing marks easy. eBay has some of these packages for sale. In addition my cam and crank seals were leaking you may want to change them out while you have the engine this far apart. Look over the tutorial carefully I decided to change both idler bearings and anything else I didn't want to go back and repair later. Some FIPG for the pump seal is nice to have on hand too. Good luck and check in if you need help.
The following users liked this post:
Returd (03-13-17)
#5
Intermediate
Thread Starter
thanks for that link, all the info available is helpful.
I'm thinking of doing all the suggested change parts from the original link, and possibly the rad hoses and serpentine belt too. I'll do the cam and crank seals while in there, thanks for the suggestion. What is FPIG, some sort of instant gasket?
This will be a good intro into this particular engine, I'm a Ford guy.
I'll likely do a refresh including the timing belt on my parts car engine as well but that will be done later on an engine stand.
I'm thinking of doing all the suggested change parts from the original link, and possibly the rad hoses and serpentine belt too. I'll do the cam and crank seals while in there, thanks for the suggestion. What is FPIG, some sort of instant gasket?
This will be a good intro into this particular engine, I'm a Ford guy.
I'll likely do a refresh including the timing belt on my parts car engine as well but that will be done later on an engine stand.
#6
Driver
iTrader: (3)
thanks for that link, all the info available is helpful.
I'm thinking of doing all the suggested change parts from the original link, and possibly the rad hoses and serpentine belt too. I'll do the cam and crank seals while in there, thanks for the suggestion. What is FPIG, some sort of instant gasket?
This will be a good intro into this particular engine, I'm a Ford guy.
I'll likely do a refresh including the timing belt on my parts car engine as well but that will be done later on an engine stand.
I'm thinking of doing all the suggested change parts from the original link, and possibly the rad hoses and serpentine belt too. I'll do the cam and crank seals while in there, thanks for the suggestion. What is FPIG, some sort of instant gasket?
This will be a good intro into this particular engine, I'm a Ford guy.
I'll likely do a refresh including the timing belt on my parts car engine as well but that will be done later on an engine stand.
Thread
Thread Starter
Forum
Replies
Last Post
Lexus082
Performance & Maintenance
6
12-19-12 03:11 PM
Romadoc
ES - 1st to 4th Gen (1990-2006)
8
04-16-08 07:12 AM