Performance & Maintenance Engine, forced induction, intakes, exhausts, torque converters, transmissions, etc.

SC 400 Stalling

Thread Tools
 
Search this Thread
 
Old 07-31-10, 06:49 PM
  #1  
S142jz
Pole Position
Thread Starter
iTrader: (2)
 
S142jz's Avatar
 
Join Date: Jul 2009
Location: Kill devil hills, NC aka OBX
Posts: 320
Likes: 0
Received 2 Likes on 2 Posts
Default SC 400 Stalling

Ok so my buddy owns a 93 SC 400. He has been haveing issues with the car. He tells me that it will run fine untill it warms up then it stalls.

He allows the car to cool off for a few hours and then the car will start right back up and run fine till maybe 10miles. Then the ***** (sc400) will stall out again and wont start.

He tells me when it beging to act up alot of heat from the motor enters the cockpit.

I realy don't know what to look for I've got 2 sc300 and an s14 with the 2jz. So I'm kinda lost as to what to look for on this sc400.

Thanks for the Help fellas..............
Old 08-05-10, 09:03 PM
  #2  
S142jz
Pole Position
Thread Starter
iTrader: (2)
 
S142jz's Avatar
 
Join Date: Jul 2009
Location: Kill devil hills, NC aka OBX
Posts: 320
Likes: 0
Received 2 Likes on 2 Posts
Default

Any suggestions will be great.
Old 08-06-10, 10:08 AM
  #3  
MrBrock
Driver
 
MrBrock's Avatar
 
Join Date: May 2010
Location: Iowa
Posts: 188
Likes: 0
Received 0 Likes on 0 Posts
Default

Could be a bad idle air control valve
Old 08-08-10, 04:07 PM
  #4  
S142jz
Pole Position
Thread Starter
iTrader: (2)
 
S142jz's Avatar
 
Join Date: Jul 2009
Location: Kill devil hills, NC aka OBX
Posts: 320
Likes: 0
Received 2 Likes on 2 Posts
Default

I don't think its the iacv. B/c the car looses power. If it was the iacv it would idel like crap but in this case idel is fine. till it warms up and looses power.

anymore suggestions I could take a look at ????????? Thanks.
Old 08-08-10, 10:28 PM
  #5  
S142jz
Pole Position
Thread Starter
iTrader: (2)
 
S142jz's Avatar
 
Join Date: Jul 2009
Location: Kill devil hills, NC aka OBX
Posts: 320
Likes: 0
Received 2 Likes on 2 Posts
Default

Ok so I took the caps and rotor buttons off. They looked good except for the one (rotor button ) on the pass side has a crack on the side but doesn't reach the top were the metal is.

Also looked at the coil but they look great not cracks or burn marks.



Any ideass would help n
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
SilentNuke
Performance & Maintenance
10
03-24-12 07:26 AM
tenshu2k
SC- 1st Gen (1992-2000)
22
04-30-11 09:19 AM
92S0ARER
SC- 1st Gen (1992-2000)
30
01-17-07 09:00 AM
Will P
SC- 1st Gen (1992-2000)
3
06-06-04 09:42 AM



Quick Reply: SC 400 Stalling



All times are GMT -7. The time now is 12:14 AM.