singel turbo manifold problem???
#1
Driver School Candidate
Thread Starter
Join Date: Jun 2008
Location: nj
Posts: 17
Likes: 0
Received 0 Likes
on
0 Posts
singel turbo manifold problem???
Ok i wanna do NA-T and DO NOT want to do a TT swap in the car. So i called full race and they don't make a manifold that will fit a turbo bigger than a GT-40 on a NA motor?? i have a GT-47 that i never used on any of my other projects so i'm putting it on the SC. So anyone that has a NA-T with a turbo as large as mine or bigger what manifold do you have and who makes it? i hear of guys making big #'s with NA-T so you have to be using something? please help!!!
Thanks for your time, warren
Thanks for your time, warren
#3
Pole Position
Join Date: May 2008
Location: australia
Posts: 346
Likes: 0
Received 0 Likes
on
0 Posts
suggestion for
kit
http://www.otomoto.com.au/kkr/turbos/jza80kit.html
turbo
http://www.otomoto.com.au/kkr/KKR480.html
"Manifold flange plate (for use as a spacer or to fabricate a new manifold)"
kit
http://www.otomoto.com.au/kkr/turbos/jza80kit.html
turbo
http://www.otomoto.com.au/kkr/KKR480.html
"Manifold flange plate (for use as a spacer or to fabricate a new manifold)"
#4
Driver School Candidate
Thread Starter
Join Date: Jun 2008
Location: nj
Posts: 17
Likes: 0
Received 0 Likes
on
0 Posts
That will make the GT-47 fit on the car and the hood shut fine? I'm not getting a different turbo for the car. So get a manifold with a T-4 flange on it or make a 2" spacer for the manifold?
#5
Driver School Candidate
Thread Starter
Join Date: Jun 2008
Location: nj
Posts: 17
Likes: 0
Received 0 Likes
on
0 Posts
The full race manifold has a T-4 flange on it. They say that anything bigger than a gt-40 compressor hits the distributor. So still stumped. i really really don't wanna put out 3K more for a TT motor when all i will use is block bare head and crank. everything else i wont be using.
#6
Pole Position
iTrader: (3)
Join Date: May 2008
Location: NC
Posts: 260
Likes: 0
Received 0 Likes
on
0 Posts
go research this question on ClubNA-T or Supra Forums. Plenty of people run larger turbos than yours on these cars, and there are plenty of helpful resources out there. If you have to ask, then you probably shouldn't try it. But if you really need to, Boost Brothers just released a manifold for these cars that will support some very large compressors.
#7
Lexus Champion
iTrader: (5)
The full race manifold has a T-4 flange on it. They say that anything bigger than a gt-40 compressor hits the distributor. So still stumped. i really really don't wanna put out 3K more for a TT motor when all i will use is block bare head and crank. everything else i wont be using.
1) Get a T4 Flange plate and weld it on so that the turbo is angled away from the distributor
2) Get a distributor cap off a toyota 4runner V6 and an extra #2 ignition cable and bolt it on the distributor.
More info in Mark's section (TurboXS) on clubna-t.com
Thread
Thread Starter
Forum
Replies
Last Post
scmaluco
Performance & Maintenance
5
11-22-12 08:34 PM