North Texas Lexus New Member Intro Post here!!!!!!!!!!!!
Driver School Candidate
Joined: Mar 2009
Posts: 15
Likes: 0
From: Texas
Hey, my name is Joe and this is my car, the Devil's little sister. I'm still trying to finish fixing her up. My latest project will be a cold air intake that i hope to have purchased and installed within the next month.
What part of North Texas are you from?
Lead Lap
Joined: Oct 2006
Posts: 581
Likes: 0
From: texas
Hello,
First name's Aaron. I'm not really that new, but I haven't formally introduced myself on this subforum.
Location is Dallas Area.
I drive an sc300 w/ gte swap (shocker huh) with an auto to manual conversion.
Did most of the work myself. Except for things that require welding (driveshaft, shift linkage extension, bungs that needed welding)
No good pics of the car as a whole, but here's an engine bay pic.
I sometimes go to the wednesday night meets, but usually no one pays attention to it cause other than the engine/tranny its stock. Haha which I don't mind much. But I would like to discuss about sc's with other enthusiasts locally.
Specifically I'm looking for somone who has an auto to manual swap done, so I can see if I did anything wrong with it etc etc.
I still need to clean up quite a bit in the presentation of the car/ engine. Any tips appreciated. Thanks!
First name's Aaron. I'm not really that new, but I haven't formally introduced myself on this subforum.
Location is Dallas Area.
I drive an sc300 w/ gte swap (shocker huh) with an auto to manual conversion.
Did most of the work myself. Except for things that require welding (driveshaft, shift linkage extension, bungs that needed welding)
No good pics of the car as a whole, but here's an engine bay pic.
I sometimes go to the wednesday night meets, but usually no one pays attention to it cause other than the engine/tranny its stock. Haha which I don't mind much. But I would like to discuss about sc's with other enthusiasts locally.
Specifically I'm looking for somone who has an auto to manual swap done, so I can see if I did anything wrong with it etc etc.
I still need to clean up quite a bit in the presentation of the car/ engine. Any tips appreciated. Thanks!
Last edited by lemmiewink; Jun 21, 2009 at 11:13 PM.
Lead Lap
Joined: Jun 2008
Posts: 765
Likes: 0
From: Texas
Hello Aaron! I think I've met you once at a wednesday meet. Sandstone beige correct? I'm still stock over here...
Hello,
First name's Aaron. I'm not really that new, but I haven't formally introduced myself on this subforum.
Location is Dallas Area.
I drive an sc300 w/ gte swap (shocker huh) with an auto to manual conversion.
Did most of the work myself. Except for things that require welding (driveshaft, shift linkage extension, bungs that needed welding)
No good pics of the car as a whole, but here's an engine bay pic.
I sometimes go to the wednesday night meets, but usually no one pays attention to it cause other than the engine/tranny its stock. Haha which I don't mind much. But I would like to discuss about sc's with other enthusiasts locally.
Specifically I'm looking for somone who has an auto to manual swap done, so I can see if I did anything wrong with it etc etc.
I still need to clean up quite a bit in the presentation of the car/ engine. Any tips appreciated. Thanks!
First name's Aaron. I'm not really that new, but I haven't formally introduced myself on this subforum.
Location is Dallas Area.
I drive an sc300 w/ gte swap (shocker huh) with an auto to manual conversion.
Did most of the work myself. Except for things that require welding (driveshaft, shift linkage extension, bungs that needed welding)
No good pics of the car as a whole, but here's an engine bay pic.
I sometimes go to the wednesday night meets, but usually no one pays attention to it cause other than the engine/tranny its stock. Haha which I don't mind much. But I would like to discuss about sc's with other enthusiasts locally.
Specifically I'm looking for somone who has an auto to manual swap done, so I can see if I did anything wrong with it etc etc.
I still need to clean up quite a bit in the presentation of the car/ engine. Any tips appreciated. Thanks!