Door Lock Actuator - is this the correct part
#1
Lead Lap
Thread Starter
Join Date: May 2006
Location: Ca
Posts: 518
Likes: 0
Received 0 Likes
on
0 Posts
Door Lock Actuator - is this the correct part
http://cgi.ebay.com/ebaymotors/LEXUS...Q5fAccessories
Its the drivers side front door, 2005, is this the correct part?
Its the drivers side front door, 2005, is this the correct part?
#3
cory,
that look like it...but really if your going in that deep wh ynot just buy the maguchi motor for lile 10.00 and replace the motor?
Since your doing it yourself its not hard just opening the housing and replacing the motor.
https://www.clublexus.com/forums/gs-...ators-diy.html
Here is the write up i followed. It was almost dead on...but this will give you the road map if you plan on doing this your self. Mine was done a year ago and I have had zero problems.
that look like it...but really if your going in that deep wh ynot just buy the maguchi motor for lile 10.00 and replace the motor?
Since your doing it yourself its not hard just opening the housing and replacing the motor.
https://www.clublexus.com/forums/gs-...ators-diy.html
Here is the write up i followed. It was almost dead on...but this will give you the road map if you plan on doing this your self. Mine was done a year ago and I have had zero problems.
Last edited by buggs384; 10-28-10 at 09:51 AM. Reason: more info
#4
Lexus Champion
Buggs,
Did you have to take the window out to get the actuator out?
Thanks,
VQT
Did you have to take the window out to get the actuator out?
Thanks,
VQT
cory,
that look like it...but really if your going in that deep wh ynot just buy the maguchi motor for lile 10.00 and replace the motor?
Since your doing it yourself its not hard just opening the housing and replacing the motor.
https://www.clublexus.com/forums/gs-...ators-diy.html
Here is the write up i followed. It was almost dead on...but this will give you the road map if you plan on doing this your self. Mine was done a year ago and I have had zero problems.
that look like it...but really if your going in that deep wh ynot just buy the maguchi motor for lile 10.00 and replace the motor?
Since your doing it yourself its not hard just opening the housing and replacing the motor.
https://www.clublexus.com/forums/gs-...ators-diy.html
Here is the write up i followed. It was almost dead on...but this will give you the road map if you plan on doing this your self. Mine was done a year ago and I have had zero problems.
#6
Lead Lap
Thread Starter
Join Date: May 2006
Location: Ca
Posts: 518
Likes: 0
Received 0 Likes
on
0 Posts
To be honest I would rather spend $10 bucks. : )
My main issue is that there seems to be a bit of confusion on which is the correct replacement motor. I want to make sure i'm putting the motor with the correct torque and power figures in. Some of the motors also need to be modified because the shaft is not D shaped.
All that sounds like a head ache to me.....
My main issue is that there seems to be a bit of confusion on which is the correct replacement motor. I want to make sure i'm putting the motor with the correct torque and power figures in. Some of the motors also need to be modified because the shaft is not D shaped.
All that sounds like a head ache to me.....
Last edited by bigcory; 11-01-10 at 10:49 AM.
#7
I can send you the part number....The only modification i did was to make a flat spot on the rounded shaft ot the motor...i just used a grin ding wheel and took my time checking fit every so often...took no more than 3 mins to grind and check for fit
Trending Topics
#8
Moderator
You could also use an inexpensive Dremel tool to grind the flat spot
Thread
Thread Starter
Forum
Replies
Last Post
Riemy6
LS - 3rd Gen (2001-2006)
2
09-18-16 10:18 AM
srgone
GS - 3rd Gen (2006-2011)
2
08-23-11 10:05 AM