Pic Request: ISF with CF splitters
03-06-12, 06:39 PM
#46
Lexus Champion
Thread Starter
iTrader: (7)
Join Date: Dec 2005
Location: TX
Posts: 3,617
Likes: 0
Received 0 Likes
on
0 Posts
I got mine from auto technik and they are ABS with overlay. I wasn't aware of a full CF version! I would have gotten that one instead. I think the key to making it look good is to not have it stick out so much... I like it better when it's almost flush with the bumper, but that's just my taste.
With that said, mine is holding up very well even after 3 years. No problems at all. I scraped the edges a bit, but it's on fine. It's a matter of installing it properly.
Here are a couple of pix:
With that said, mine is holding up very well even after 3 years. No problems at all. I scraped the edges a bit, but it's on fine. It's a matter of installing it properly.
Here are a couple of pix:
or all u guys in general..
self tapping screws? or bolts and nuts?
03-06-12, 07:16 PM
#47
What no one is mentioning is that these are like a shell on the underside, that has not been visible in any of the pictures.
They are not a solid 1/2 inch ABS plastic. They are only about 1/4 inch thick with a curved front edge to give the illusion of thickness.
Digger08
They are not a solid 1/2 inch ABS plastic. They are only about 1/4 inch thick with a curved front edge to give the illusion of thickness.
Digger08
03-06-12, 07:17 PM
#48
What no one is mentioning is that these are like a shell on the underside, that has not been visible in any of the pictures.
They are not a solid 1/2 inch ABS plastic. They are only about 1/4 inch thick with a curved front edge to give the illusion of thickness. Not to detract from what they are....just letting you know.
They are not a solid 1/2 inch ABS plastic. They are only about 1/4 inch thick with a curved front edge to give the illusion of thickness. Not to detract from what they are....just letting you know.
03-06-12, 08:15 PM
#49
Lead Lap
Join Date: Sep 2010
Location: TX
Posts: 477
Likes: 0
Received 0 Likes
on
0 Posts
What no one is mentioning is that these are like a shell on the underside, that has not been visible in any of the pictures.
They are not a solid 1/2 inch ABS plastic. They are only about 1/4 inch thick with a curved front edge to give the illusion of thickness. Not to detract from what they are....just letting you know.
They are not a solid 1/2 inch ABS plastic. They are only about 1/4 inch thick with a curved front edge to give the illusion of thickness. Not to detract from what they are....just letting you know.
03-06-12, 10:55 PM
#50
I just got mine in today.
Yup right about that
Anyone know a good shop in SoCal I can get this installed? Not comfortable drilling holes myself.
What no one is mentioning is that these are like a shell on the underside, that has not been visible in any of the pictures.
They are not a solid 1/2 inch ABS plastic. They are only about 1/4 inch thick with a curved front edge to give the illusion of thickness. Not to detract from what they are....just letting you know.
They are not a solid 1/2 inch ABS plastic. They are only about 1/4 inch thick with a curved front edge to give the illusion of thickness. Not to detract from what they are....just letting you know.
Anyone know a good shop in SoCal I can get this installed? Not comfortable drilling holes myself.
03-08-12, 01:25 PM
#56
Just got back from getting them installed.
Got the install done for $60 at Supreme Power in SoCal, Talk to Eric. He did a pretty good job.
Got the install done for $60 at Supreme Power in SoCal, Talk to Eric. He did a pretty good job.
Last edited by cha7Li3; 04-22-13 at 03:45 PM.
03-08-12, 08:55 PM
#59
I actually wanted for it to stick out more then the others I saw on this thread. I figured if I were going to put a splitters on, might as well make it more noticable.
Thanks. The guy who installed it for me eyed it just right.
Here are 2 more pics with less sunlight. (easier to see)
Thanks. The guy who installed it for me eyed it just right.
Here are 2 more pics with less sunlight. (easier to see)
Last edited by cha7Li3; 03-08-12 at 08:59 PM.
