View Poll Results: Crawl / MTS - model year/trim upgrade survey
2010 - Base - Added Crawl
0
0%
2011 - Base - Added Crawl
0
0%
2011 - Premium (stock Crawl) - Added MTS
0
0%
2012 - Base - Added Crawl
0
0%
2012 - Premium (stock Crawl) - Added MTS
0
0%
2014 Base - Added Crawl
0
0%
2015 Base - Added Crawl
0
0%
2015 Premium - Added Crawl
0
0%
2016 Base - Added Crawl
0
0%
2016 Premium - Added Crawl
0
0%
2017 Base - Added Crawl
0
0%
2017 Premium - Added Crawl
0
0%
2017 Luxury - Added Crawl/MTS
0
0%
2018 Base - Added Crawl
0
0%
2018 Luxury - Added Crawl
0
0%
2019 Base - Added Crawl
0
0%
2019 Premium - Added Crawl
0
0%
2019 Luxury - Added Crawl
0
0%
2019 Luxury - Added Crawl/MTS
0
0%
Voters: 125. You may not vote on this poll
MOD: Crawl Control (CC) and Multi Terrain Select (MTS)
#736
Hello All!
New to the forum, Just got my 2013 GX 460 Premium last month and ordered the module and switches from OEMVehicleParts last week, but it would appear they have not shipped or processed the order, how long does it normally take?
New to the forum, Just got my 2013 GX 460 Premium last month and ordered the module and switches from OEMVehicleParts last week, but it would appear they have not shipped or processed the order, how long does it normally take?
#737
Super Moderator
Thread Starter
TomCruiser: Are you actuating the crawl ON/OFf switch at end of zero point before turning vehicle off?
i use that same TS cable from eBay. Works well. Win OS version shouldn’t matter...64 bit support just lets in run on newer gear
i use that same TS cable from eBay. Works well. Win OS version shouldn’t matter...64 bit support just lets in run on newer gear
#738
Racer
Thanks hzhao!
I following the instruction for zero point cal using SST wire. Before 4 times in 8s, the ABS and slip are off. After 4 times in 8s, I did see the slip light come on again and ABS is flashing as well. However, for CC cal, I follow the step and turn of the engine, the connect pin4 & pin12, once I push the CC switch, there was no CC light and no info of +/- in the display when I toggled +/- switch. I just curious if I do need to turn the engine to IG for SST wire approach? If not, why at end of the CC cal step k(turn of engine, again for SST if it was already turn off at 1st step in section b).
Anyway, once I remove pin4/pin8 and turn on the engine, I can see the CC light. When I push the CC button & +/- switch. I can see info in the display but slip off is flashing(in 4lo). So I think the CC part/cable is connected correctly but no CC cal. However, in normal 4hi, slip off light is on and 4lo is flashing. I can't turn them off even after re-do zero pt cal. I'm afraid if I missing some steps, or can anyone share the CC using SST?
BTW, anyone using min VCI type of techstream from ebay to do the zero pt cal & CC cal? Does 32/64-bits os matters?
Thanks!
I following the instruction for zero point cal using SST wire. Before 4 times in 8s, the ABS and slip are off. After 4 times in 8s, I did see the slip light come on again and ABS is flashing as well. However, for CC cal, I follow the step and turn of the engine, the connect pin4 & pin12, once I push the CC switch, there was no CC light and no info of +/- in the display when I toggled +/- switch. I just curious if I do need to turn the engine to IG for SST wire approach? If not, why at end of the CC cal step k(turn of engine, again for SST if it was already turn off at 1st step in section b).
Anyway, once I remove pin4/pin8 and turn on the engine, I can see the CC light. When I push the CC button & +/- switch. I can see info in the display but slip off is flashing(in 4lo). So I think the CC part/cable is connected correctly but no CC cal. However, in normal 4hi, slip off light is on and 4lo is flashing. I can't turn them off even after re-do zero pt cal. I'm afraid if I missing some steps, or can anyone share the CC using SST?
BTW, anyone using min VCI type of techstream from ebay to do the zero pt cal & CC cal? Does 32/64-bits os matters?
Thanks!
#739
Super Moderator
Thread Starter
Not sure how readily vendors are stocking these now but if anyone is looking to do Crawl Control and/or MTS on their 460 ...Matt @ OEMVehicleparts says he has 6 or 7 of each coming in tomorrow. He does offer up a discount code for 50% off shipping ---> Code: CLUBLEXUS
#740
Driver School Candidate
After I finished zero pt, I turn off the engine and connect pin4 & pin12, then start the CC on/off switch but there was no light comes on.
#741
Driver School Candidate
Seems that one of the steps didn't complete. You can always go through this process again starting from beginning. I have used Techstream, there is a member here used SST wire and had no problem to complete the process. As far as the VCI cable and software, as Acrad said, both 32/64 are supported. The only trick part is the MiniVCI driver for windows, I have not had success for finding the 64bit drier, nor I was able to installed 32 bit driver running in 32 bit emulating mode. I ended up using an old window xp notebook for the techstream.
#742
Driver School Candidate
Not sure how readily vendors are stocking these now but if anyone is looking to do Crawl Control and/or MTS on their 460 ...Matt @ OEMVehicleparts says he has 6 or 7 of each coming in tomorrow. He does offer up a discount code for 50% off shipping ---> Code: CLUBLEXUS
#743
Super Moderator
Thread Starter
TomCruiser:
Not likely defective since it is overall pretty simple from an electronics standpoint inside.
Here are few that have done paper clip method:
https://www.clublexus.com/forums/gx-...l#post10223316
https://www.clublexus.com/forums/gx-...l#post10226509
Not sure where in CA you are might might reach out to this guy as well.
https://www.clublexus.com/forums/gx-...l#post10228152
https://www.clublexus.com/forums/gx-...l#post10291734
Not likely defective since it is overall pretty simple from an electronics standpoint inside.
Here are few that have done paper clip method:
https://www.clublexus.com/forums/gx-...l#post10223316
https://www.clublexus.com/forums/gx-...l#post10226509
Not sure where in CA you are might might reach out to this guy as well.
https://www.clublexus.com/forums/gx-...l#post10228152
https://www.clublexus.com/forums/gx-...l#post10291734
#744
If you're located in SoCal (south bay area) I'd be willing to help out. I don't have tech stream, but I was able to do the zero point with the paperclip method (though I just used two wires).
The following 2 users liked this post by KJ6IRM:
Acrad (10-22-18),
TomCruiser (10-22-18)
#745
After trying the process about 6 times. i I tried the dac turn on then off at the end of the process before finishing. This was done in the test mode. This completed it for me. If anyone is having problems, try that Dac On then Off at the very last step. Not sure if this is what finally finished it for me or not, but it worked after 6 tries, that was the only thing different i did to make this work.
#746
Racer
Yes turning CC on/off at the last step before exiting is working for many people including me.
#747
Super Moderator
Thread Starter
EDIT: I will move it up to the top.
Good to hear you got it working.
A while back I added this quote from Coinball to bottom of first FAQ post.
https://www.clublexus.com/forums/gx-...l-control.html
Good to hear you got it working.
A while back I added this quote from Coinball to bottom of first FAQ post.
https://www.clublexus.com/forums/gx-...l-control.html
Last edited by Acrad; 10-31-18 at 02:04 PM.
#748
Driver School Candidate
I’m interested in adding my own switches for crawl control instead of buying a new switch console. Anyone willing to donate their old non-CC switch console to me for experimentation?
Has anyone already done this as a hack instead of a swap of switch consoles?
Has anyone already done this as a hack instead of a swap of switch consoles?
#749
Just installed the crawl switch....working so far, haven't driven in a straight line yet...but was able to get crawl control working...unfortunately I was sent the wrong module so still need to do multi terrain.
The following users liked this post:
Acrad (11-01-18)
#750
Super Moderator
Thread Starter