keeps popping up
05-23-12, 09:31 AM
Lead Lap
Thread Starter
Join Date: Oct 2010
Location: New Jersey
Posts: 698
Likes: 0
Received 0 Likes
on
0 Posts
keeps popping up
dose anybody know to stop the box on from keep coming up on the right side
ok think i got it
Last edited by bacardi; 05-23-12 at 09:35 AM .
05-23-12, 02:07 PM
Moderator
Join Date: Dec 2009
Location: CA - San Diego
Posts: 3,135
Huh??????????
What box? I'm confused.
Last edited by VVTiBob; 05-24-12 at 11:57 AM .
05-23-12, 03:12 PM
Lead Lap
Thread Starter
Join Date: Oct 2010
Location: New Jersey
Posts: 698
Likes: 0
Received 0 Likes
on
0 Posts
05-23-12, 04:44 PM
Lead Lap
Join Date: Mar 2012
Location: PA
Posts: 431
Likes: 0
Received 0 Likes
on
0 Posts
Remove the muffler bearings. Then it will stop.
05-24-12, 08:02 AM
Moderator
Join Date: Jan 2007
Location: VA
Posts: 2,791
Likes: 0
Probably just low on hood coolant.
Just top that off and you should be fine.
05-24-12, 08:57 AM
Moderator
Join Date: Feb 2007
Location: NM
Posts: 2,089
Quote:
Originally Posted by
bacardi
dose anybody know to stop the box on from keep coming up on the right side
ok think i got it
I think your post is missing a word or two.
05-24-12, 09:47 AM
Racer
Join Date: Feb 2007
Location: DC
Posts: 1,637
This happened to me a couple of years ago. It turned out that the box dampener on the right side had gone bad and so there was nothing to keep it from coming up. The dealership wanted almost $5,000 to install a new dampener. I did it myself in about 10 minutes. Problem solved.
05-24-12, 09:55 AM
Rookie
Join Date: Apr 2011
Location: Cambridgeshire
Posts: 89
Likes: 0
Check the flange plate, because its probably gone out of skew on the treadle.
05-24-12, 05:11 PM
Pole Position
Join Date: Jul 2010
Location: Quebec
Posts: 365
Likes: 0
Check the kick-down fluid in the reservoir... Level might be low!
05-24-12, 06:12 PM
Driver
Join Date: Mar 2012
Location: CA
Posts: 130
Likes: 0
Received 0 Likes
on
0 Posts
Radiator bearings, definately radiator bearings.
05-24-12, 06:23 PM
Lead Lap
Join Date: Jan 2004
Location: Florida
Posts: 450
Likes: 0
Quote:
Originally Posted by
sebtown
Radiator bearings, definately radiator bearings.
Not the carbeurator?
05-25-12, 05:03 AM
Lead Lap
Join Date: Mar 2012
Location: PA
Posts: 431
Likes: 0
Received 0 Likes
on
0 Posts
Boy, you learn so much neat information on this site!!
05-25-12, 05:44 AM
Driver School Candidate
Join Date: Apr 2012
Location: New Jersey
Posts: 28
Likes: 0
Received 0 Likes
on
0 Posts
Quote:
Originally Posted by
ser67
Check the flange plate, because its probably gone out of skew on the treadle.
Check the Finigan Pin then check the flow of the Dynoflow.
05-25-12, 01:02 PM
Driver
Join Date: Mar 2012
Location: CA
Posts: 130
Likes: 0
Received 0 Likes
on
0 Posts
May also mant to check for poper alignment of the Johnson Rod
05-25-12, 01:09 PM
Moderator
Join Date: Dec 2009
Location: CA - San Diego
Posts: 3,135
I checked my "Johnson" and it is aligned properly.
sorry, just couldn't resist