Mail man brought me some goodies today
#1
Pole Position
Thread Starter
iTrader: (2)
Join Date: Feb 2009
Location: TN
Posts: 334
Likes: 0
Received 0 Likes
on
0 Posts
Mail man brought me some goodies today
I got me some toys today
Ordered these just the other day from Enjuku Racing for my SC300. Going to probably install these on my stock n/a motor until I finish compiling all the parts for my 1JZ/R154 swap so that I can at least drive the car if I need it. Maybe can even break them in on a weak motor that won't have a big turbo hanging off of it so there won't be any temptation to break it in on boost. It's a billet steel flywheel for the 1JZ and a Stage 3 clutch/pressure plate, 520 ft lbs I think it the rating.
These came in way quicker than the Spec clutch/pressure plate I ordered for my 300ZXTT a few years ago. I know they normally build them to order but this must have been sitting on a shelf ready to go already.
Ordered these just the other day from Enjuku Racing for my SC300. Going to probably install these on my stock n/a motor until I finish compiling all the parts for my 1JZ/R154 swap so that I can at least drive the car if I need it. Maybe can even break them in on a weak motor that won't have a big turbo hanging off of it so there won't be any temptation to break it in on boost. It's a billet steel flywheel for the 1JZ and a Stage 3 clutch/pressure plate, 520 ft lbs I think it the rating.
These came in way quicker than the Spec clutch/pressure plate I ordered for my 300ZXTT a few years ago. I know they normally build them to order but this must have been sitting on a shelf ready to go already.
#4
Pole Position
Thread Starter
iTrader: (2)
Join Date: Feb 2009
Location: TN
Posts: 334
Likes: 0
Received 0 Likes
on
0 Posts
Today he brought me this:
It's a Precision big shaft 63mm turbo. Basic 4" inlet, 2.5" outlet, t4 flange. He said it has a .68 hot side but I don't know, being an older turbo it's hard to find information on it. It's supposed to be 3" v-band, even told him if it wasn't t4 and 3" v-band I wouldn't be able to use it since 3" is what all the downpipes I've come across are and he said it was 3", but upon receiving it in the mail and measuring, it's a damn 3.5" >: (
It's a Precision big shaft 63mm turbo. Basic 4" inlet, 2.5" outlet, t4 flange. He said it has a .68 hot side but I don't know, being an older turbo it's hard to find information on it. It's supposed to be 3" v-band, even told him if it wasn't t4 and 3" v-band I wouldn't be able to use it since 3" is what all the downpipes I've come across are and he said it was 3", but upon receiving it in the mail and measuring, it's a damn 3.5" >: (
#6
We only deliver amazon parcels on sundays and holidays, that just started but once christmas rolls around we will be delivering all parcels on sundays i bet.
#7
Pole Position
Thread Starter
iTrader: (2)
Join Date: Feb 2009
Location: TN
Posts: 334
Likes: 0
Received 0 Likes
on
0 Posts
I did read up on it some today after I posted this and heard from others what you are saying Ali. It's hard to get a good measurement with a tape measure on a small round hole, but laying a piece of paper flat across it and putting pencil marks where the inner part of the hole was then measuring that with a tape measure, it appears to be 3" inner diamater...unless some v-bands come in 2 9/10 inches lol
Trending Topics
#9
Yea the whole company...the post office i work is far from metro lol about 2 hours from dc in the country so idk maybe there still testing be they did have comercials running on tv.
Thread
Thread Starter
Forum
Replies
Last Post
shaodome
SC400 / 300 Classifieds
1
09-06-11 07:36 PM