"THE" clublexus eaton m90!
#1
Lexus Test Driver
Thread Starter
iTrader: (6)
Join Date: May 2010
Location: Colorado Springs, CO
Posts: 1,442
Likes: 0
Received 4 Likes
on
4 Posts
"THE" clublexus eaton m90!
So I am thinking about being the next owner of this supercharger that started with scottrunot, then to jdmmuscle, axmily, meshguy etc whoever has it now if they are the forums. I really need to find a few things out first.
My main concern is POWER. Why no one ever dyno'd with the darn charger is beyond me! Not trying to spend over $3000(realistically) and make barely 300whp. Which leads me to believe why everyone keeps reselling it because they realize it doesn't make much power.
I have searched far and wide about the m90, but none that I have found have been ported.
So does anyoneeeeeeeee know the figure this thing should put out with a 7psi pulley or say a 10psi pulley if/when I relocated the coolant hose? I have aem fic-8 now but not going to install it until I find my platform, if this falls through I will more then likely upgrade to aem v2 and go boost.
OR
Get rid of the 1uz and go gte or lsx, just months after I put my 6 speed in the 1uz is such a good contender to other engines but lacks so much in readily available information and aftermarket. It's starting to bother me esp since I have done the m/t swap and now's there's really nowhere to go with the car besides spend a fortune to make it faster for the price of another engine swap
My main concern is POWER. Why no one ever dyno'd with the darn charger is beyond me! Not trying to spend over $3000(realistically) and make barely 300whp. Which leads me to believe why everyone keeps reselling it because they realize it doesn't make much power.
I have searched far and wide about the m90, but none that I have found have been ported.
So does anyoneeeeeeeee know the figure this thing should put out with a 7psi pulley or say a 10psi pulley if/when I relocated the coolant hose? I have aem fic-8 now but not going to install it until I find my platform, if this falls through I will more then likely upgrade to aem v2 and go boost.
OR
Get rid of the 1uz and go gte or lsx, just months after I put my 6 speed in the 1uz is such a good contender to other engines but lacks so much in readily available information and aftermarket. It's starting to bother me esp since I have done the m/t swap and now's there's really nowhere to go with the car besides spend a fortune to make it faster for the price of another engine swap
Last edited by iridebmx; 04-02-14 at 09:56 PM.
#2
Look in the GS forums. I always go there whenever I'm looking at a new performance mods for my 1UZ. They (for some reason) have done more with the 1UZ then us SC guys have..
#3
Lexus Test Driver
iTrader: (44)
Join Date: Jan 2007
Location: Maryland /Germantown
Posts: 5,139
Likes: 0
Received 7 Likes
on
7 Posts
If i were you i would Single Turbo that 1UZ if it's in great shape, get some electric Fans and you have all the room you need for you plumbings!!
Or
Your other option is gte swap...
Or
Your other option is gte swap...
#7
Driver School Candidate
Join Date: Sep 2013
Location: Arkansas
Posts: 33
Likes: 0
Received 0 Likes
on
0 Posts
Trending Topics
#9
Lexus Test Driver
Thread Starter
iTrader: (6)
Join Date: May 2010
Location: Colorado Springs, CO
Posts: 1,442
Likes: 0
Received 4 Likes
on
4 Posts
How I look at new cars is like this. Sure they make 250-300 from factory but with forced induction added almost all of them hit a limit close to 400hp without having to open up the motor. And its the same with the 1uz. Now there is one impressive little sucker! The k24; its such a great motor. If only honda would make a v8!
Also theory 5150, the car drives great and is enough for a daily driver. It's everything I expected out of a m/t 1uz but being up in the mountains the car really feels the altitude and its kinda boring me. I am getting the craving for more power.
I am now searching for a lq9..... would be nice if I could attach my trans to it
isn't it a beaut!
Also theory 5150, the car drives great and is enough for a daily driver. It's everything I expected out of a m/t 1uz but being up in the mountains the car really feels the altitude and its kinda boring me. I am getting the craving for more power.
I am now searching for a lq9..... would be nice if I could attach my trans to it
isn't it a beaut!
Last edited by 99SC42; 04-05-14 at 05:34 AM. Reason: Not a vendor.
#10
I've got a Maxima with the VQ35, rated at 265hp. My guess is it's putting down about 220-230 to the wheels. A good deal quicker than my stock 1UZ. Not sure what the current gen Maxima claims but my guess is another 25-50hp. Just putting my input here.
Sorry OP, no answer for your question.
Sorry OP, no answer for your question.
#13
Pole Position
iTrader: (2)
Join Date: Jul 2008
Location: Texas/Pennsylvania
Posts: 236
Likes: 0
Received 0 Likes
on
0 Posts
How I look at new cars is like this. Sure they make 250-300 from factory but with forced induction added almost all of them hit a limit close to 400hp without having to open up the motor. And its the same with the 1uz. Now there is one impressive little sucker! The k24; its such a great motor. If only honda would make a v8!
Also theory 5150, the car drives great and is enough for a daily driver. It's everything I expected out of a m/t 1uz but being up in the mountains the car really feels the altitude and its kinda boring me. I am getting the craving for more power.
I am now searching for a lq9..... would be nice if I could attach my trans to it
EDIT: of the century! http://collinsadapters.com/index.php...ter-plate.html
isn't it a beaut!
Also theory 5150, the car drives great and is enough for a daily driver. It's everything I expected out of a m/t 1uz but being up in the mountains the car really feels the altitude and its kinda boring me. I am getting the craving for more power.
I am now searching for a lq9..... would be nice if I could attach my trans to it
EDIT: of the century! http://collinsadapters.com/index.php...ter-plate.html
isn't it a beaut!
My god I would so love to do the LQ9 with the z trans but I'm a little hesitant about cutting the trans or know any shop that would do that.
Thread
Thread Starter
Forum
Replies
Last Post
kez
Performance & Maintenance
4
09-18-10 10:09 AM