Door lock actuator motor replaceable???
#16
My rear RHS door isn't locking it unlocks. I have seen central locking kits for sale for about $20 which may or may not suit. I really haven't tried to fix it yet. I have another car which has similar locks pontiac fiero so may see if they could be suited either way.
#17
Lexus Champion
If it LOCKS but doesn't UNLOCK, it's not the lock motor. That is if it locks strong but doesn't make any effort to unlock. It is in the contacts in the switch or elsewhere, but not in the lock motor.
#18
Rookie
Thread Starter
I sourced them from eBay. Just type in FC280PC-22125 and you will see plenty of prices and options. Not the real MABUCHI motors, but made in CHINA (of course like everything else now). Cheapest I found was about $8 shipped each.
#19
Lexus Champion
The REAL Mabuchi motors ARE made in China. When I cut them apart in my DIL's RX, they were definitely all original, and all made in China. As a mater of fact I have taken small (similar but not identical Mabuchi) motors out of other rechargeable and DC and AC devices and they were ALL made in China. And her RX is a '99 built in about June, '98.
#20
Rookie
Thread Starter
The REAL Mabuchi motors ARE made in China. When I cut them apart in my DIL's RX, they were definitely all original, and all made in China. As a mater of fact I have taken small (similar but not identical Mabuchi) motors out of other rechargeable and DC and AC devices and they were ALL made in China. And her RX is a '99 built in about June, '98.
BTW: you keep referring to DIL, what or who is DIL?
#22
Well, I hate to say it, but I am going to have to dig into this DIY myself. Yes, my 2000 RX300 front passenger side door lock no longer actuates. With some trepidation I am reading, searching (did that code58), and learning how to do this. I guess I am going to try and get four of the actuators (maybe five as I will probably screw one up...) and will then have three in case other doors break. Wish me luck down in San Diego, CA!
Nick V
Nick V
#23
Driver School Candidate
I have been looking at the different piggy back ideas and sounds very good, but I have one question. Why not just hook up the new actuator to the door manual lock mechanism above the interior door handle being the rod is already in place and you would be using the same cam anyway? In other words mount the new actuator as shown in the photo but fasten the two rods together and you won't have to worry about the cam locking lever housing.
#24
Moderator
I have been looking at the different piggy back ideas and sounds very good, but I have one question. Why not just hook up the new actuator to the door manual lock mechanism above the interior door handle being the rod is already in place and you would be using the same cam anyway? In other words mount the new actuator as shown in the photo but fasten the two rods together and you won't have to worry about the cam locking lever housing.
The DIY is to attach the rod (piggy back) to the thumb-lever.
Salim
#26
Driver School Candidate
Join Date: Jan 2011
Location: Tennessee
Posts: 15
Likes: 0
Received 0 Likes
on
0 Posts
I want to thank code58 for all the information you have added to this thread. Your time and information is greatly appreciated. Thank you! As for everyone else, thank you for adding to this discussion. There is nothing more empowering than for us to share what we know.
My 2000 RX front driver door lock died three years ago and the passenger front door died a year later. The back doors are the only ones that work at this time. I have been searching for a reasonable fix all this time. I have only had the driver's door off and on my work bench. It looked like to me the yoke was broken and thus the cables could not be actuated. I can still make the actuator turn so...I wonder.
As for me, I worked for Bosch as a mechanical engineer so I can see what you are saying when it comes to installation. I have to tell you, we made all the electrical motors and actuators for a ton of Ford/Lincoln/Mercury/Chrysler/Dodge/Mazda/Nissan and they were built to last the average life of a vehicle which at that time was 18.4 years. Our test showed better results so when you say the actuators shouldn't fail...I think you are right. Those suckers are almost bullet proof. As for the aftermarket ones, those look simple and solid as well. You should never have to open those door panels again. As for the Lexus door actuators...I have never seen such a cheap piece of crap in my whole life! I’ve seen cheap toys with better actuators/motors in them. Lexus should be ashamed to let that production run go so long without a change. It makes me want to look at the BMW X3 when I get ready to replace it. Thanks Toyota.
My 2000 RX front driver door lock died three years ago and the passenger front door died a year later. The back doors are the only ones that work at this time. I have been searching for a reasonable fix all this time. I have only had the driver's door off and on my work bench. It looked like to me the yoke was broken and thus the cables could not be actuated. I can still make the actuator turn so...I wonder.
As for me, I worked for Bosch as a mechanical engineer so I can see what you are saying when it comes to installation. I have to tell you, we made all the electrical motors and actuators for a ton of Ford/Lincoln/Mercury/Chrysler/Dodge/Mazda/Nissan and they were built to last the average life of a vehicle which at that time was 18.4 years. Our test showed better results so when you say the actuators shouldn't fail...I think you are right. Those suckers are almost bullet proof. As for the aftermarket ones, those look simple and solid as well. You should never have to open those door panels again. As for the Lexus door actuators...I have never seen such a cheap piece of crap in my whole life! I’ve seen cheap toys with better actuators/motors in them. Lexus should be ashamed to let that production run go so long without a change. It makes me want to look at the BMW X3 when I get ready to replace it. Thanks Toyota.
#27
Driver School Candidate
Join Date: Jan 2011
Location: Tennessee
Posts: 15
Likes: 0
Received 0 Likes
on
0 Posts
code58 I just read your reply on another thread on the details of what you found on your DILs RX. Noted. I know you are right now. The yoke is not broken as I thought before. The motor is just worn out. Thank you again.
#28
Moderator
I want to thank code58 for all the information you have added to this thread. Your time and information is greatly appreciated. Thank you! As for everyone else, thank you for adding to this discussion. There is nothing more empowering than for us to share what we know.
My 2000 RX front driver door lock died three years ago and the passenger front door died a year later. The back doors are the only ones that work at this time. I have been searching for a reasonable fix all this time. I have only had the driver's door off and on my work bench. It looked like to me the yoke was broken and thus the cables could not be actuated. I can still make the actuator turn so...I wonder.
As for me, I worked for Bosch as a mechanical engineer so I can see what you are saying when it comes to installation. I have to tell you, we made all the electrical motors and actuators for a ton of Ford/Lincoln/Mercury/Chrysler/Dodge/Mazda/Nissan and they were built to last the average life of a vehicle which at that time was 18.4 years. Our test showed better results so when you say the actuators shouldn't fail...I think you are right. Those suckers are almost bullet proof. As for the aftermarket ones, those look simple and solid as well. You should never have to open those door panels again. As for the Lexus door actuators...I have never seen such a cheap piece of crap in my whole life! I’ve seen cheap toys with better actuators/motors in them. Lexus should be ashamed to let that production run go so long without a change. It makes me want to look at the BMW X3 when I get ready to replace it. Thanks Toyota.
My 2000 RX front driver door lock died three years ago and the passenger front door died a year later. The back doors are the only ones that work at this time. I have been searching for a reasonable fix all this time. I have only had the driver's door off and on my work bench. It looked like to me the yoke was broken and thus the cables could not be actuated. I can still make the actuator turn so...I wonder.
As for me, I worked for Bosch as a mechanical engineer so I can see what you are saying when it comes to installation. I have to tell you, we made all the electrical motors and actuators for a ton of Ford/Lincoln/Mercury/Chrysler/Dodge/Mazda/Nissan and they were built to last the average life of a vehicle which at that time was 18.4 years. Our test showed better results so when you say the actuators shouldn't fail...I think you are right. Those suckers are almost bullet proof. As for the aftermarket ones, those look simple and solid as well. You should never have to open those door panels again. As for the Lexus door actuators...I have never seen such a cheap piece of crap in my whole life! I’ve seen cheap toys with better actuators/motors in them. Lexus should be ashamed to let that production run go so long without a change. It makes me want to look at the BMW X3 when I get ready to replace it. Thanks Toyota.
95 sc400 (actuator gone bad)
98 BMW 328i (actuator gone bad) ... effort to replace 1/3
Salim
#29
Lexus Champion
I want to thank code58 for all the information you have added to this thread. Your time and information is greatly appreciated. Thank you! As for everyone else, thank you for adding to this discussion. There is nothing more empowering than for us to share what we know.
My 2000 RX front driver door lock died three years ago and the passenger front door died a year later. The back doors are the only ones that work at this time. I have been searching for a reasonable fix all this time. I have only had the driver's door off and on my work bench. It looked like to me the yoke was broken and thus the cables could not be actuated. I can still make the actuator turn so...I wonder.
As for me, I worked for Bosch as a mechanical engineer so I can see what you are saying when it comes to installation. I have to tell you, we made all the electrical motors and actuators for a ton of Ford/Lincoln/Mercury/Chrysler/Dodge/Mazda/Nissan and they were built to last the average life of a vehicle which at that time was 18.4 years. Our test showed better results so when you say the actuators shouldn't fail...I think you are right. Those suckers are almost bullet proof. As for the aftermarket ones, those look simple and solid as well. You should never have to open those door panels again. As for the Lexus door actuators...I have never seen such a cheap piece of crap in my whole life! I’ve seen cheap toys with better actuators/motors in them. Lexus should be ashamed to let that production run go so long without a change. It makes me want to look at the BMW X3 when I get ready to replace it. Thanks Toyota.
My 2000 RX front driver door lock died three years ago and the passenger front door died a year later. The back doors are the only ones that work at this time. I have been searching for a reasonable fix all this time. I have only had the driver's door off and on my work bench. It looked like to me the yoke was broken and thus the cables could not be actuated. I can still make the actuator turn so...I wonder.
As for me, I worked for Bosch as a mechanical engineer so I can see what you are saying when it comes to installation. I have to tell you, we made all the electrical motors and actuators for a ton of Ford/Lincoln/Mercury/Chrysler/Dodge/Mazda/Nissan and they were built to last the average life of a vehicle which at that time was 18.4 years. Our test showed better results so when you say the actuators shouldn't fail...I think you are right. Those suckers are almost bullet proof. As for the aftermarket ones, those look simple and solid as well. You should never have to open those door panels again. As for the Lexus door actuators...I have never seen such a cheap piece of crap in my whole life! I’ve seen cheap toys with better actuators/motors in them. Lexus should be ashamed to let that production run go so long without a change. It makes me want to look at the BMW X3 when I get ready to replace it. Thanks Toyota.
I actually figured out the piggyback method when I had to replace all 4 on my DIL's RX. 2 were bad, 1 intermittent and 1 working so I replaced all 4. Explanation of what was going on in family crisis is noted earlier. I can't claim originality in coming up with piggyback, because my piggyback on DIL's RX was more like factory in cars where it is truly a separate installation, not part of the lock. I realized that the original lock assembly had to remain in place to accommodate all the other functions it performs. I used donated Ford actuators and they are still going strong at going on 5 years now. It was only later that I started doing the "easier" piggyback when someone on one of the Lexus forums did it that way and I realized it was simpler. I have done a # of them that way and must give credit to the man who saw a way that I didn't see. My wife laughs when I say I am a "recovering" perfectionist, but it's actually true.
Good luck to ALL who have not crossed this bridge yet. The $1300. they wanted for the 4 locks from Lexus, plus tax, was ALL the motivation I needed.
#30
Driver School Candidate
Join Date: Jan 2011
Location: Tennessee
Posts: 15
Likes: 0
Received 0 Likes
on
0 Posts
Thanks again to Sali and Code58. You guys are great!
I may be late to this game but it has occoured to me that the failure rate of these actuators are excellerated by the use of the doors. In other words, the constant use and the shock of slamming the doors may play a role in how soon the actuator will fail.
I may be late to this game but it has occoured to me that the failure rate of these actuators are excellerated by the use of the doors. In other words, the constant use and the shock of slamming the doors may play a role in how soon the actuator will fail.