Performance & Maintenance Engine, forced induction, intakes, exhausts, torque converters, transmissions, etc.

Did I just pull my IACV, or something else?

Thread Tools
 
Search this Thread
 
Old 03-01-14, 02:11 PM
  #1  
MongooseGA
Racer
Thread Starter
iTrader: (6)
 
MongooseGA's Avatar
 
Join Date: Feb 2005
Location: GA
Posts: 1,567
Received 12 Likes on 5 Posts
Default Did I just pull my IACV, or something else?

All,

I have been working on my '95 400 today, going through the steps to eliminate a hesitation under light acceleration.

I came to the IACV and followed the steps outline here:


Another possible culprit of hesitation is the idle air control valve. Located right on the front of the plenum you have a few options for checking it.

Click the image to open in full size.


You will have to carefully remove the plug wire tray to get to this.
Undo the 2 bolts holding it to the plenum. Disconnect the cooling lines. Disconnect the connector and pull it out.

Click the image to open in full size.

Do your resistance checks and if you feel real adventurous, connect your battery leads to it and stroke the valve to verify operation.

You can go one step further and remove the 3 phillips screws holding the stepper motor assembly to the mounting body. Now the full valve is exposed along with the motor armature. Spin it in and out a few times to verify it moves smooth. Clean it up, lube it up and reinstall. OF course replace if any readings are out of spec.
In order to follow SC400Slide's DIY tutorial, here: https://www.clublexus.com/forums/per...acv-sc400.html

It wasn't until I got the part off that I noticed how unlike mine was from the one in Slide's write up. In fact, it looks like I have an identical part to his, but it's sitting further back on the plenum, on the driver's side. See my pics below.

Now I'm stumped. The part I pulled does not have the screws to disassemble it. The other part I'll point out does. Thoughts?

Part I pulled:


Where it came from:



Other part that looks like Slide's IACV:


I will be searching as well, but I need my car back on the road by tomorrow. Hoping for the fastest responses. Thanks.

Last edited by MongooseGA; 03-01-14 at 02:14 PM.
Old 03-01-14, 03:28 PM
  #2  
Studiogeek
Lexus Champion
iTrader: (6)
 
Studiogeek's Avatar
 
Join Date: Nov 2012
Location: NYC
Posts: 2,702
Received 15 Likes on 11 Posts
Default

His is a 92'. Yours is 95'. I looked it up and saw one part for 92-93 and another for the rest. If this is accurate, that may be the problem.
Good luck. I need to do that as well.

Last edited by Studiogeek; 03-01-14 at 05:50 PM.
Old 03-01-14, 05:26 PM
  #3  
MongooseGA
Racer
Thread Starter
iTrader: (6)
 
MongooseGA's Avatar
 
Join Date: Feb 2005
Location: GA
Posts: 1,567
Received 12 Likes on 5 Posts
Default

It appears there were different part numbers for different years. Mine is PN#22270-50020.

Older ones like in the DIY are PN#22270-50010.

Couldn't guess what mine is different. Could be because the car has traction control while others didn't? Could just be the year?

Either way, has anyone successfully opened one like mine to clean? I'm a bit reluctant to put a flat edge under the plastic cap and start prying. Especially on a part that I don't know yet is bad.

Anyone able to tell if the PN# ending in 50010 would be compatible with my car? With the exception of shape of the pin I can see inside of mine, they're identical.

Last edited by MongooseGA; 03-01-14 at 06:42 PM.
Old 03-01-14, 06:35 PM
  #4  
MongooseGA
Racer
Thread Starter
iTrader: (6)
 
MongooseGA's Avatar
 
Join Date: Feb 2005
Location: GA
Posts: 1,567
Received 12 Likes on 5 Posts
Default

Looks like the top cap of my IACV is adhered to the metal base. Guess that means I won't be taking this one apart.
Old 03-01-14, 07:34 PM
  #5  
SC400slide
In Recovery Mode

iTrader: (11)
 
SC400slide's Avatar
 
Join Date: Apr 2012
Location: NM
Posts: 3,871
Received 35 Likes on 29 Posts
Default

Ok, I'll edit my DIY. 92-93 IACV's are different from 1994-later. Sorry about that. We're all still learning...
Old 03-01-14, 07:38 PM
  #6  
MongooseGA
Racer
Thread Starter
iTrader: (6)
 
MongooseGA's Avatar
 
Join Date: Feb 2005
Location: GA
Posts: 1,567
Received 12 Likes on 5 Posts
Default

No worries. The write-up was definitely great. Just unfortunate it doesn't relate to mine right now.

I'm meeting with a guy locally tomorrow to pick up a TPS and new IACV from a '97 to test out. He did seem to think that any model #IACV was interchangeable throughout the OBD1 cars.
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
Greg5OH
LS - 1st and 2nd Gen (1990-2000)
6
01-24-14 03:13 PM
Bradlex
RX - 1st Gen (1999-2003)
9
04-23-12 10:24 AM
jbobst
RX - 1st Gen (1999-2003)
7
08-21-11 11:49 AM
romeo291
Performance & Maintenance
1
09-02-09 07:21 AM
Lexmex
RX - 1st Gen (1999-2003)
9
05-17-06 08:16 PM



Quick Reply: Did I just pull my IACV, or something else?



All times are GMT -7. The time now is 11:00 AM.