93 sc400 running rough on idle
#1
Driver School Candidate
Thread Starter
Join Date: Feb 2012
Location: indiana
Posts: 27
Likes: 0
Received 0 Likes
on
0 Posts
93 sc400 running rough on idle
ok so i bought a 93 sc400 about a month ago i thought it needed a head gasket. this last saturday i finally got around to diagnosing what was wrong turns out the guy had put ign wires on it and got two backwards i switched them around and it ran real nice at higher rpms but at idle it runs a little rough i put new plugs cap and rotor on it. i put a different iac valve on from an ls 400 because i tested my old one and it was bad. i did a diagnostic check on my engine light and it was code 28. out of ideas and energy i pulled the spark plugs out and bank one was bburning normally but bank 2 was burning rich and the plugs were covered in carbon. so my question is has anyone ever had this happen on their lexus and could an o2 sensor through off the fuel ratio that much to make it run ****ty on idle?
#2
I got my SC for $800 for the same reason but I had two pairs, or half the engine, with the plug wires in the wrong order. It's a miracle it cranked at all!
I think you need to replace all the vac hoses under the hood. They're old, stiff, and dryrotted. You'll need 6-7 feet of 5/32 or 4mm hose to do them all. Things like the fuel pressure regulator and the EGR valve rely on vacuum to operate and either of them could cause a bad idle. It's a pretty simple job -- far easier than on any turbo car I ever owned!
I cleaned my ISC -- don't even think of buying a new one - you'll fall over when you see the price, replaced all the ignition components, and did all the vac hoses. I now have a solid idle, and thanks to the 12v fuel pump mod it cranks instantly too.
At some point I'm going to put together a list of everything that needs to be done to a stock 400 upon purchase. These questions pop up every few days.
I think you need to replace all the vac hoses under the hood. They're old, stiff, and dryrotted. You'll need 6-7 feet of 5/32 or 4mm hose to do them all. Things like the fuel pressure regulator and the EGR valve rely on vacuum to operate and either of them could cause a bad idle. It's a pretty simple job -- far easier than on any turbo car I ever owned!
I cleaned my ISC -- don't even think of buying a new one - you'll fall over when you see the price, replaced all the ignition components, and did all the vac hoses. I now have a solid idle, and thanks to the 12v fuel pump mod it cranks instantly too.
At some point I'm going to put together a list of everything that needs to be done to a stock 400 upon purchase. These questions pop up every few days.
#3
In Recovery Mode
iTrader: (11)
Sorry to jump...
I just got a 1992 SC400.
Seats in front are not very good, (1 is vinyl)
Chugs at low speeds and when slowing down, surges, like the third member is going out.
It has 148,xxx.
About the surging and chugs, I cleaned the IACV, TPS, and throttle body.
I have not cleaned the MAF yet, and will check the coil in the mere future.
Cleaned fuel injectors extremely, and changed spark plugs and wires.
What would be the most likely to check out?? im thinking the maf is dirty...
I just got a 1992 SC400.
Seats in front are not very good, (1 is vinyl)
Chugs at low speeds and when slowing down, surges, like the third member is going out.
It has 148,xxx.
About the surging and chugs, I cleaned the IACV, TPS, and throttle body.
I have not cleaned the MAF yet, and will check the coil in the mere future.
Cleaned fuel injectors extremely, and changed spark plugs and wires.
What would be the most likely to check out?? im thinking the maf is dirty...
#4
Is the TPS calibrated properly? The how-to is easy to find with a quick search. Basically you verify the idle switch on one set of contacts and and the variable resistance throughout the range of operation on the other.
They say the MAF is too sensitive to clean without breaking it. I don't get why -- I've cleaned similar sensors in other cars many times without issue but I haven't touched the one in this car yet. Try unplugging your MAF and see if the car runs better. That's a good place to start.
Don't forget the vac hoses either. It's quick and easy and eliminates one more potential issue.
They say the MAF is too sensitive to clean without breaking it. I don't get why -- I've cleaned similar sensors in other cars many times without issue but I haven't touched the one in this car yet. Try unplugging your MAF and see if the car runs better. That's a good place to start.
Don't forget the vac hoses either. It's quick and easy and eliminates one more potential issue.
#5
In Recovery Mode
iTrader: (11)
Thanks
I'll try.
I heard what happened when some people cleaned their MAF sensor.
It broke, and 1000 bucks slipped away...
Could it be the EGR?
It sounds mechanical to me.
Only when it warms up, it has very slight tachometer movement when its rough.
No loss of power or anything, (accelerates quickly)
also, how do I check the coil, cuz it might be the coil... 1 out of 2 may be broke
(FYI I fiddled W/ the TPS. when moved top the right idle went higher...
thanks for your help
I'll try.
I heard what happened when some people cleaned their MAF sensor.
It broke, and 1000 bucks slipped away...
Could it be the EGR?
It sounds mechanical to me.
Only when it warms up, it has very slight tachometer movement when its rough.
No loss of power or anything, (accelerates quickly)
also, how do I check the coil, cuz it might be the coil... 1 out of 2 may be broke
(FYI I fiddled W/ the TPS. when moved top the right idle went higher...
thanks for your help
#6
Lead Lap
iTrader: (8)
I think you need to replace all the vac hoses under the hood. They're old, stiff, and dryrotted. You'll need 6-7 feet of 5/32 or 4mm hose to do them all. Things like the fuel pressure regulator and the EGR valve rely on vacuum to operate and either of them could cause a bad idle.
I changed out the vacuum hoses and early indications are that the FPR is okay and it was just a bad vacuum issue. Several of the hoses were in pretty poor shape, as you described. With the new hoses in place, all four start-ups in a row were within a couple tenths of a second, as opposed to the usual 2-5 seconds of cranking. Fingers crossed that that holds true in the coming days.
Oh, your estimate on the total length was a bit low, though. 7' left me with about 4" left over, but that's without doing the two long hoses that run under the air intake. To do everything is probably 10-11'. I was going to get 8' at the store but they had a 7' section already cut so I figured that would be perfect.
#7
Lead Lap
iTrader: (8)
Oh, your estimate on the total length was a bit low, though. 7' left me with about 4" left over, but that's without doing the two long hoses that run under the air intake. To do everything is probably 10-11'. I was going to get 8' at the store but they had a 7' section already cut so I figured that would be perfect.
While working on that and throttle body cleaning, I noticed one of the bigger vacuum hoses that connects to the air intake had a split where it fits over the barb. There was enough slack to just cut that part off, since I didn't have that size hose on hand and didn't have enough light to see where it went down below. I'd like to think cold start and idle were improved after finishing up all the vacuum stuff, but I've thought that before and eventually decided it only partially addressed things...
Thread
Thread Starter
Forum
Replies
Last Post
JDM2jz23
Performance & Maintenance
1
01-28-17 08:31 AM