Corner "Nike" and Fog Light Replacement Pics
#18
V-LEDS has them in a bunch of colors.
they're the best LED company i've used... the brightest i've seen.
http://www.v-leds.com/194-168-158-LED/c506139-1-2/
i'm gonna do this.
they're the best LED company i've used... the brightest i've seen.
http://www.v-leds.com/194-168-158-LED/c506139-1-2/
i'm gonna do this.
#19
oh and i found these instructions to get to the bulb in another thread.
looks like you don't have to pull the bumper.
Originally Posted by Shibumi1 View Post
i did it without removing the whole bumper.. remove the grill (1) 10mm socket. the remove the plastic clips holding grille on each corner.then its easy as pulling the grille forward gently as u release the locking tabs (4).. once the grille is out you'll see a plastic trim w foam tucked behind the bumper trim on either side of the grille opening.bend it down then you'll see 2 wiring harnesses unclip them or bend the metal tabs holding them in place an you'll see the bulb socket reach in an turn it counterclockwise an pop the socket out.
looks like you don't have to pull the bumper.
Originally Posted by Shibumi1 View Post
i did it without removing the whole bumper.. remove the grill (1) 10mm socket. the remove the plastic clips holding grille on each corner.then its easy as pulling the grille forward gently as u release the locking tabs (4).. once the grille is out you'll see a plastic trim w foam tucked behind the bumper trim on either side of the grille opening.bend it down then you'll see 2 wiring harnesses unclip them or bend the metal tabs holding them in place an you'll see the bulb socket reach in an turn it counterclockwise an pop the socket out.
The following users liked this post:
CRSO (03-22-20)
#24
Driver School Candidate
Join Date: Nov 2010
Location: CA
Posts: 17
Likes: 0
Received 0 Likes
on
0 Posts
#25
Moderator
If so that is easy to replace.
Turn your wheel inward, remove the fender lining, then reach up and turn the bulb socket to replace the bulb.
#26
Driver School Candidate
Join Date: Nov 2010
Location: CA
Posts: 17
Likes: 0
Received 0 Likes
on
0 Posts
I need to replace the clearance (nike shape) light.
#27
Maybe they did it that way, but were doing other work for you that required dropping the bumper
Last edited by cmasten; 02-24-11 at 08:58 PM.
#28
The top one is Piaa-H376... that helps a lot!
Product page from Autobacs:
http://www.autobacs.com/shop/g/g4960311238744/
The bottom pic looks like the regular 9006/9007...
Which set you put in for the Nike light? Top or bottom??
-------
edit:
Autoback removed their web link, here is another link to Piaa manufacturer:
http://www.piaa.co.jp/products/car/l...ve/tera.html#2
Product page from Autobacs:
http://www.autobacs.com/shop/g/g4960311238744/
The bottom pic looks like the regular 9006/9007...
Which set you put in for the Nike light? Top or bottom??
-------
edit:
Autoback removed their web link, here is another link to Piaa manufacturer:
http://www.piaa.co.jp/products/car/l...ve/tera.html#2
#29
Driver School Candidate
Looks great, I was looking into doing mines too. I was told you could use 921 bulb as well which is super bright which won't break the bank, but still little concerned on the power. It draws a higher current 1.4A at ltitle over 17watt compare to approximately 0.4A on the stock bulb.
Thread
Thread Starter
Forum
Replies
Last Post