Rear hub bearings-grinding noise- Going crazy!!
#16
Driver School Candidate
Thread Starter
Join Date: Nov 2014
Location: KY
Posts: 11
Likes: 0
Received 0 Likes
on
0 Posts
Yes I believe so made by Timken also there is a pink dot on each side of the differential where the axles bolt on so I'm curious if the axles aren't connected properly to the differential. It looks like it doesn't matter how they go on to me. Also how do you put the bearings back in the old cv axles is there a trick to this? I'm also wondering if I was sold the right bearings but the axles go into the hub very easy to a point but when you tighten it up the hub won't move like maybe I have the wrong bearings
Last edited by steve1961; 12-28-14 at 12:52 PM.
#17
It looks like these cars do not use taper roller wheel bearings. The nut that holds the axle in the bearings is torqued to 253 ft lbs.
The bearing should be kinda self contained and the races would have the proper preload spacer.
http://lexus.sewellparts.com/oem-cat...S400-1992.html
After the nut is tightened if it is way too hard to turn then the bearing is at fault somehow.
In the picture it still looks like the seal is either not in far enough or the hub is not in far enough. The new preloaded bearings should have a small amount of resistance. Unlike taper rollers that need a bit of play, the double ball bearings use a bit of preload.
Maybe they were not pressed in correctly. The pressure needs to be on the larger diameter part that fits in the hole, not being applied to an area that puts the press in pressure on the *****. If it was pressed against the ***** then it is probably a junk bearing now. Unless the guy pressing was a trainee, any automotive machine shop should know how to do it right. Though I did have a shop goof up some geo metro wheel bearings one time, I didn't watch them press it in. It didn't last a month.
The bearing should be kinda self contained and the races would have the proper preload spacer.
http://lexus.sewellparts.com/oem-cat...S400-1992.html
After the nut is tightened if it is way too hard to turn then the bearing is at fault somehow.
In the picture it still looks like the seal is either not in far enough or the hub is not in far enough. The new preloaded bearings should have a small amount of resistance. Unlike taper rollers that need a bit of play, the double ball bearings use a bit of preload.
Maybe they were not pressed in correctly. The pressure needs to be on the larger diameter part that fits in the hole, not being applied to an area that puts the press in pressure on the *****. If it was pressed against the ***** then it is probably a junk bearing now. Unless the guy pressing was a trainee, any automotive machine shop should know how to do it right. Though I did have a shop goof up some geo metro wheel bearings one time, I didn't watch them press it in. It didn't last a month.
Last edited by dicer; 12-28-14 at 09:28 PM.
#18
Driver School Candidate
Thread Starter
Join Date: Nov 2014
Location: KY
Posts: 11
Likes: 0
Received 0 Likes
on
0 Posts
It looks like these cars do not use taper roller wheel bearings. The nut that holds the axle in the bearings is torqued to 253 ft lbs.
The bearing should be kinda self contained and the races would have the proper preload spacer.
http://lexus.sewellparts.com/oem-cat...S400-1992.html
After the nut is tightened if it is way too hard to turn then the bearing is at fault somehow.
In the picture it still looks like the seal is either not in far enough or the hub is not in far enough. The new preloaded bearings should have a small amount of resistance. Unlike taper rollers that need a bit of play, the double ball bearings use a bit of preload.
Maybe they were not pressed in correctly. The pressure needs to be on the larger diameter part that fits in the hole, not being applied to an area that puts the press in pressure on the *****. If it was pressed against the ***** then it is probably a junk bearing now. Unless the guy pressing was a trainee, any automotive machine shop should know how to do it right. Though I did have a shop goof up some geo metro wheel bearings one time, I didn't watch them press it in. It didn't last a month.
The bearing should be kinda self contained and the races would have the proper preload spacer.
http://lexus.sewellparts.com/oem-cat...S400-1992.html
After the nut is tightened if it is way too hard to turn then the bearing is at fault somehow.
In the picture it still looks like the seal is either not in far enough or the hub is not in far enough. The new preloaded bearings should have a small amount of resistance. Unlike taper rollers that need a bit of play, the double ball bearings use a bit of preload.
Maybe they were not pressed in correctly. The pressure needs to be on the larger diameter part that fits in the hole, not being applied to an area that puts the press in pressure on the *****. If it was pressed against the ***** then it is probably a junk bearing now. Unless the guy pressing was a trainee, any automotive machine shop should know how to do it right. Though I did have a shop goof up some geo metro wheel bearings one time, I didn't watch them press it in. It didn't last a month.
Last edited by steve1961; 12-29-14 at 06:14 PM. Reason: update
#20
Driver School Candidate
Thread Starter
Join Date: Nov 2014
Location: KY
Posts: 11
Likes: 0
Received 0 Likes
on
0 Posts
Yea I updated my last post to say it was the dust shields that were grinding. The mechanic popped off both dust shields and it turns nice and smooth. Almost done just have to put the brakes on and then after it sitting on car jacks for almost two months I can finally say it's finished!!
#22
Driver School Candidate
Thread Starter
Join Date: Nov 2014
Location: KY
Posts: 11
Likes: 0
Received 0 Likes
on
0 Posts
Well took it for a test drive today and it did fine until I found out I had no brakes. Took it back home and seen brake fluid by the rear tire so jacked it up and my whole brake line is all rusted and corroded and leaking. My fuel lines were the same way but had a friend replace all the rusted part so now I guess I need to do the same thing with the brake lines. I think I'm going to take it to the shop because not sure how hard it would be to fix. I know you can cut off the bad part and replace with a new line using compression fittings so I don't know if I'll attempt it or not.
Thread
Thread Starter
Forum
Replies
Last Post