High-quality plain license plate frame?
#1
Pole Position
Thread Starter
High-quality plain license plate frame?
Just got a "new" 2013 LS 460 F Sport. I want a plain chrome or polished stainless steel 2-hole plate frame. So many of them to have negative reviews on Amazon and other sites. Where can I get a pair that are worthy of my car?
#2
Advanced
I went to Pep Boyz and after about 45 minutes looking at the selection of frames, I purchased a very plain stainless steel, two hole frame for about $24....... It looks good and I am happy with it. Griots garage www.griotsgarage.com has some nice looking frames too.
TIP! Make sure you don't buy a frame that covers up ANY of the license plate letters (EZ to write ticket) and use stainless steel screws.
TIP! Make sure you don't buy a frame that covers up ANY of the license plate letters (EZ to write ticket) and use stainless steel screws.
Last edited by Chuckinnj; 01-19-16 at 06:16 PM.
#3
In theory I'd like to have a polished steel or aluminum frame.
In practice I've never seen one that was as tasteful as the factory trim on a car. So I go frameless.
If you find one that's really good, post it for us to see.
In practice I've never seen one that was as tasteful as the factory trim on a car. So I go frameless.
If you find one that's really good, post it for us to see.
#4
Driver School Candidate
This is the one I have. Looks great and has held up for over a year.
#5
Pole Position
My two holders are from the dealership I bought the car from. I've never really given it much thought until this thread. Perhaps it's time to find some non branded kits.
#7
Instructor
iTrader: (1)
This is the one I installed on my LS. Expensive but well made, seller has LS460 as well..........
http://www.ebay.com/itm/07-12-NEW-LE...cAAOxy~dNTJ5Zc
http://www.ebay.com/itm/07-12-NEW-LE...cAAOxy~dNTJ5Zc
Trending Topics
#8
Pole Position
Thread Starter
Thanks. I see Amazon comments about this one saying that the edges are unfinished and sharp. Is that the case?
This is the one I have. Looks great and has held up for over a year.
Amazon.com: License Plate Holder - Stainless Steel Kit - Includes Screw Cover Caps & Screws - Premium Quality SAE 304SS Performance Automotive Grade Metal Polished To A Chrome Plated Mirror Finish! - 2 Hole Frame Holder Anti Theft Screw Covers - DFDM National: Automotive
Amazon.com: License Plate Holder - Stainless Steel Kit - Includes Screw Cover Caps & Screws - Premium Quality SAE 304SS Performance Automotive Grade Metal Polished To A Chrome Plated Mirror Finish! - 2 Hole Frame Holder Anti Theft Screw Covers - DFDM National: Automotive
#9
Pole Position
I bought several plain 2-hole stainless steel plates from Auto Attire. No rust issues despite being in the rust belt. Large selection. Get the clear plexiglass cover for the plate too. http://www.autoattire.com/stainless-...te-frames.html
#10
Get the clear plexiglass cover for the plate too. http://www.autoattire.com/stainless-...te-frames.html
#11
Pole Position
Good point. I have never had an issue in IL or across the numerous states I have crossed logging hundreds of thousands of miles with a clear, fully transparent plastic plate cover - not a "photomaskcover" or similar. In IL, clear plate covers are specifically recognized by the Sec. of State as permissible as long as they remain clear and do not obstruct the visibility of the plates. (There are plenty of cameras in IL too.) Maybe having a law enforcement affinity plate helps.
#12
Lexus Fanatic
I've bought multiple frames from Auto Attire and think they're quite good. I have these 3D frames on my LS:
They also make plain frames with a wide and a narrow bottom.
I have always run the plexiglas cover, illegal in MD but never had any issues, even during traffic stops. You would have to go up and feel them to know that they were covered, the plexiglass is matte finished.
They also make plain frames with a wide and a narrow bottom.
I have always run the plexiglas cover, illegal in MD but never had any issues, even during traffic stops. You would have to go up and feel them to know that they were covered, the plexiglass is matte finished.
#13
Driver School Candidate
Not that I noticed. However, I've always put small felt pads (like the ones that go on the bottom of chairs to protect floors) on the back of the license plate so no metal touches the paint.
#15
This is what I have on my LS. It is of solid good quality chrome and looks very nice. The package does not show the chrome very well, but be assured it has the look and feel of Lexus quality.