Vsc, abs, vsc off lights on
#16
while you DID fix the broken LBJ you did NOT fix the speed sensor that got ripped when the LBJ broke. you can either repair the sensor yourself with a OHM meter, some solder, and some patience or buy a new one and replace it....but those lights will not go away till THAT issue is addressed.
BTW if u do replace it i wouldnt mind buying the old one for a spare or we
BTW if u do replace it i wouldnt mind buying the old one for a spare or we
what do they run? I'll surely give it to you for cheap if I can figure out how to get a new one replaced if needed
#17
Lexus Fanatic
iTrader: (182)
yes it PHYSICALLY is attached but inside the wiring its ripped someplace. the rubber coating has to be opened, if you OHM it out you will find there is indeed a break in the wire and then you would just need to trace it back to find out where it ripped and then solder/reattach it.
jefftsai used to have a DIY with pics but all the pics are gone and he hasnt ever updated the pics...
i know for awhile he was fixing them for people but i dunno if he does anymore or not.
new i think they $160-200
#18
i dont mean this in a bad way but are you mechanically inclined at all? some people are not so im trying to grasp if you even capable of doing the repair.
yes it PHYSICALLY is attached but inside the wiring its ripped someplace. the rubber coating has to be opened, if you OHM it out you will find there is indeed a break in the wire and then you would just need to trace it back to find out where it ripped and then solder/reattach it.
jefftsai used to have a DIY with pics but all the pics are gone and he hasnt ever updated the pics...
i know for awhile he was fixing them for people but i dunno if he does anymore or not.
new i think they $160-200
yes it PHYSICALLY is attached but inside the wiring its ripped someplace. the rubber coating has to be opened, if you OHM it out you will find there is indeed a break in the wire and then you would just need to trace it back to find out where it ripped and then solder/reattach it.
jefftsai used to have a DIY with pics but all the pics are gone and he hasnt ever updated the pics...
i know for awhile he was fixing them for people but i dunno if he does anymore or not.
new i think they $160-200
#23
So disconnecting the battery for 30 minutes did not work.
Jumping E1 to Tc also did not work, unless i didn't do it correctly. The red BRAKE warning light started blinking with a constant beep - I then jumped out the car, removed the jumper, shot the ignition, replaced the short pin, and started the car. All the amber lights are still on VSC and ABS
Jumping E1 to Tc also did not work, unless i didn't do it correctly. The red BRAKE warning light started blinking with a constant beep - I then jumped out the car, removed the jumper, shot the ignition, replaced the short pin, and started the car. All the amber lights are still on VSC and ABS
#24
Driver School Candidate
Join Date: Oct 2011
Location: UAE
Posts: 20
Likes: 0
Received 0 Likes
on
0 Posts
Try to Reset ECU just remove the battery for 1 min i hope this will help you even once i got my all dashboard lights on just removed battery now it is 4 months i dont have dashboard lights on. just try
#25
#26
c1223 is general ABS control malfunctiion code.
c1233 is yaw rate sensor.
c0205 is for the left front speed sensor.
Id start with the speed sensor.
Measure resistance between each of terminals 1 and 2 of speed sensor connector.
Resistance: 1.4 − 1.8 kΩ
Next measure resistance between terminal 1 or 2 of speed sensor connector and body ground.
Resistance: 1 MΩ or higher
If those are ok then it's probably in the wiring.
c1233 is yaw rate sensor.
c0205 is for the left front speed sensor.
Id start with the speed sensor.
Measure resistance between each of terminals 1 and 2 of speed sensor connector.
Resistance: 1.4 − 1.8 kΩ
Next measure resistance between terminal 1 or 2 of speed sensor connector and body ground.
Resistance: 1 MΩ or higher
If those are ok then it's probably in the wiring.
#27
c1223 is general ABS control malfunctiion code.
c1233 is yaw rate sensor.
c0205 is for the left front speed sensor.
Id start with the speed sensor.
Measure resistance between each of terminals 1 and 2 of speed sensor connector.
Resistance: 1.4 − 1.8 kΩ
Next measure resistance between terminal 1 or 2 of speed sensor connector and body ground.
Resistance: 1 MΩ or higher
If those are ok then it's probably in the wiring.
c1233 is yaw rate sensor.
c0205 is for the left front speed sensor.
Id start with the speed sensor.
Measure resistance between each of terminals 1 and 2 of speed sensor connector.
Resistance: 1.4 − 1.8 kΩ
Next measure resistance between terminal 1 or 2 of speed sensor connector and body ground.
Resistance: 1 MΩ or higher
If those are ok then it's probably in the wiring.
#28
#29
just had my ball joint done and the vsc and abs lights are on, car drives fine, do i need to replace anything, i reset the ecu and lights still on, how long can i drive before serious damade?
#30
You won't have serious damage, but it is dangerous to not have abs or Vsc.