8052JZ's NA-T Build
#63
Thank you sir! ^^^^^^^^
Front end is back on! Yes I know, the bumper looks a bit jacked and needs a wash but that will all be changed with maybe a shine kit and deffidently new paint. But thats a little later on down the road. I also wet sanded/polished the headlights.
I'm shooting to get the car street worthing for this weeked so I can take her for a drive to a local BBQ meet.
Up next is some exhaust work.
Front end is back on! Yes I know, the bumper looks a bit jacked and needs a wash but that will all be changed with maybe a shine kit and deffidently new paint. But thats a little later on down the road. I also wet sanded/polished the headlights.
I'm shooting to get the car street worthing for this weeked so I can take her for a drive to a local BBQ meet.
Up next is some exhaust work.
#64
Running out of updates to post lol
Quick shot of the steering wheel (needs a clean tho) Does anyone know how to get rid of the airbag light besides pulling the bulb? I wired everything correclty and the light still stays on. Any thoughts? oh notice how the steering wheel is perferated to match the seats?
Also going to shorten up the noise filter to get rid of all that wire mess so it sits under the the front cover.
Quick shot of the steering wheel (needs a clean tho) Does anyone know how to get rid of the airbag light besides pulling the bulb? I wired everything correclty and the light still stays on. Any thoughts? oh notice how the steering wheel is perferated to match the seats?
Also going to shorten up the noise filter to get rid of all that wire mess so it sits under the the front cover.
#65
To follow the last pic in the previous post I was able to get rid of at least 2ft or so of wire from the GE igniter and I also shortened the noise filter and tucked it away. They bay is dirty too, lol
Also started on the exhaust, as you can see I've got a few things lying around that I can make use of. it’s all 3" with a straight through magnaflow maganapak into dual pro 1 mufflers I had on before this build. Hopefully its not to loud after the mufflers are on. Dont mind the Greddy rattle can, its not going to be used.
and theres a sneak peack of the R154 billet trans Ill be working on soon
Also started on the exhaust, as you can see I've got a few things lying around that I can make use of. it’s all 3" with a straight through magnaflow maganapak into dual pro 1 mufflers I had on before this build. Hopefully its not to loud after the mufflers are on. Dont mind the Greddy rattle can, its not going to be used.
and theres a sneak peack of the R154 billet trans Ill be working on soon
#67
I got the cal from another member on here that got it tuned for his setup and he let me use his cal to get me going. Ill have to ask him before I start sharing the file.
Here's my setup
AEM v1
COP w/ 7mgte cps
550cc rx7 injectors
300L fuel pump
t60-1 garret
38mm tial open WG
stock GE HG (until I swap my rebuilt head and TT HG)
GE intake plunem
3" exhaust
AEM analog wideband
glowshift boost and oil pressure guages
#72
Got the exhaust all done and doing this on your back SUCKS!!! I’m more sore doing this than a good day at the gym. Anyway, it’s all 3" with a magnapak muffler to tone it down with 2 pro1 axle back mufflers. Then I sprayed it down with some 2000*f exhaust paint. Hopefully this won’t scrape that bad.
Dont mind the messy garage. This weekend is clean up day.
Dont mind the messy garage. This weekend is clean up day.
Last edited by 8052JZ; 01-22-13 at 12:28 PM.