ClubLexus - Lexus Forum Discussion - Search Results

 
Search: Posts Made By: Ali SC3
Showing results 1 to 25 of 497
Search took 1.09 seconds.
09-18-18, 09:22 AM
Replies: 3,679
Views: 706,661
Posted By Ali SC3

Looks pretty good, with an AFR of 10.3 raise the...

Looks pretty good, with an AFR of 10.3 raise the boost up until its in the mid 11's (like 11.5) and see what power it puts down, maybe like 17-18 psi.
You can use a boost cut controller to avoid...
09-16-18, 07:25 PM
Replies: 3,679
Views: 706,661
Posted By Ali SC3

davv, might be an intake piping leak or something...

davv, might be an intake piping leak or something with the map sensor.

SC, it can be normal but a fuel filter might not be a bad idea if you don't know when it was done.
I would do the 12v relay...
09-14-18, 03:41 PM
Replies: 9
Views: 324
Posted By Ali SC3

Sounds like you have a whole bunch of research...

Sounds like you have a whole bunch of research ahead, don't worry about the cams the stock ones will give you the early torque you are looking for.
Most na-t builds keep the stock cams and make...
09-14-18, 07:59 AM
Replies: 3,679
Views: 706,661
Posted By Ali SC3

That is 100% it, took me a while to figure it out...

That is 100% it, took me a while to figure it out when I had it routed wrong and it leans the afr out worse and worse as you run it. You should never plug that line, alot of people seem to do that...
09-12-18, 02:44 PM
Replies: 3,679
Views: 706,661
Posted By Ali SC3

What did you do with the gas tank vent in the...

What did you do with the gas tank vent in the engine bay? It goes to the charcoal canister stock which alot of people remove and do random stuff with the lines.

If it is at all plugged or not...
09-12-18, 02:31 PM
Replies: 3
Views: 178
Posted By Ali SC3

Sounds familiar ...

Sounds familiar
https://www.clublexus.com/forums/performance-and-maintenance/890682-cel-code-31-sc300.html

The headgasket alone won't make it run rough like that, you wouldn't really notice the...
Forum: Build Threads
09-11-18, 05:24 PM
Replies: 678
Views: 78,026
Posted By Ali SC3

Kahn, the tps can most definitely affect the idle...

Kahn, the tps can most definitely affect the idle characteristics on the stock ecu. If it is in the right position, you will hear the engine change sounds when you put in the jumper to check the...
09-10-18, 09:49 AM
Replies: 3,679
Views: 706,661
Posted By Ali SC3

what fuel pump are you using? If you want to put...

what fuel pump are you using? If you want to put a denso or anything more than a walboro, then run regular automotive 12v relay that is triggered by the stock fuel ecu (drivers side B pillar thing...
Forum: Build Threads
09-05-18, 02:37 PM
Replies: 74
Views: 9,263
Posted By Ali SC3

Sup man, yeah its been a minute, when you...

Sup man, yeah its been a minute, when you inviting me out to Md :D
haha yeah those were good times man, I remember busting out my soldering iron and the whole wiring kit and I was already working on...
Forum: Build Threads
08-31-18, 09:11 AM
Replies: 678
Views: 78,026
Posted By Ali SC3

That could very likely be it, the picture I think...

That could very likely be it, the picture I think is trying to show the spring pack facing the transmission.. but hard to say for sure.
Alot of pull type transmissions flip the disc around because...
08-30-18, 03:48 PM
Replies: 185
Views: 43,526
Posted By Ali SC3

the green piece or the silver looking solder...

the green piece or the silver looking solder piece? if its the green piece, yes you will need another one.
if its the silver looking solder goop, then its just a small piece of wire and some...
Forum: Build Threads
08-28-18, 10:39 PM
Replies: 10
Views: 377
Posted By Ali SC3

They do try and connect, but I am not sure if...

They do try and connect, but I am not sure if that would fail it overall by itself.
As long as I have a backup I can go that route, the sc300 vvti ecu/harness is a good idea.
Should I get the...
08-28-18, 11:56 AM
Replies: 3,679
Views: 706,661
Posted By Ali SC3

Its been a long time but I want to say its M8....

Its been a long time but I want to say its M8. Same size as alot of the studs on the intake manifold side (exhaust side the studs are usually M10 I want to say)
Drill it out a little larger if you...
Forum: Build Threads
08-28-18, 10:48 AM
Replies: 10
Views: 377
Posted By Ali SC3

That was my original plan was to put a vvti head...

That was my original plan was to put a vvti head on it, but since this truck has emissions I figured going with the non vvti head would be simpler and I could run an obd2 GTE ecu if needed.
I was...
Forum: Build Threads
08-28-18, 08:25 AM
Replies: 10
Views: 377
Posted By Ali SC3

A picture from the Colorado Supra BBQ meet over...

A picture from the Colorado Supra BBQ meet over the weekend. Good turnout, almost 20 mk4's by lunch time.. perfect weather and the BBQ was really good!!
...
Forum: Build Threads
08-27-18, 03:10 PM
Replies: 10
Views: 377
Posted By Ali SC3

2jzge Taco build

(2001 Double Cab Tacoma 4x4) + (1995 2jzge na-t w/quick spool valve) + (R150F 4x4) = :agreed:

This swap is going to take me a while so stay tuned, will post progress as it happens, but I'll try...
08-22-18, 10:32 PM
Replies: 3,679
Views: 706,661
Posted By Ali SC3

The coils have 12v and the other wire gets...

The coils have 12v and the other wire gets grounded by the ignitor. are you sure they are not sparking?
it could be lots of things but its probably the wiring. a bad ecu or map sensor will spark...
08-16-18, 10:18 AM
Replies: 3,679
Views: 706,661
Posted By Ali SC3

I remember having to gap down to .026-.028 on the...

I remember having to gap down to .026-.028 on the stock distributor, but with the vvti coils I was fine with the .032 stock gap but I did have the tt headgasket.

maybe grab a set of the Bkr7eix...
08-15-18, 01:08 PM
Replies: 3,679
Views: 706,661
Posted By Ali SC3

Yeah gap them down to .026-.028 then. you are...

Yeah gap them down to .026-.028 then. you are getting breakup earlier cause of the stock compression. gapping them down is the easy part, its if you go too far and have to open up the gap.. that is...
Forum: Build Threads
08-15-18, 01:06 PM
Replies: 74
Views: 9,263
Posted By Ali SC3

^that's cause you are a wiring master now :D

^that's cause you are a wiring master now :D
08-14-18, 12:52 PM
Replies: 3,679
Views: 706,661
Posted By Ali SC3

It is very difficult to foul iridiums that fast,...

It is very difficult to foul iridiums that fast, I have abused them over and over again and they usually work just fine after a proper cycle.
I would guess maybe just the gap is too large then. pull...
08-09-18, 11:33 PM
Replies: 3,679
Views: 706,661
Posted By Ali SC3

you should just have to swap the signal wire over...

you should just have to swap the signal wire over at the ecu to the right spot.
I don't remember anymore but its one the first post where you need to move it to, where the pin is I would look it...
08-09-18, 10:31 AM
Replies: 3,679
Views: 706,661
Posted By Ali SC3

dav is that the GTE main tps? opposite of the GE...

dav is that the GTE main tps? opposite of the GE tps? if so then flip the pins from stock like you noted. that should do it, maybe try another tps or check the wires for power ground, see what the...
08-09-18, 10:25 AM
Replies: 3,679
Views: 706,661
Posted By Ali SC3

It kind of makes sense to do it like that but it...

It kind of makes sense to do it like that but it doesn't look too great, I am not surprised you have a bad connection there with that kind of splice.
The stock wires are usually a little brittle by...
Forum: Build Threads
08-08-18, 10:51 AM
Replies: 678
Views: 78,026
Posted By Ali SC3

That is great news! congrats on the start up. ...

That is great news! congrats on the start up. all those are pretty minor and sure you will get it sorted out soon.
You can try getting some of the air out of the PS pump, sometimes they make a...
Showing results 1 to 25 of 497
 


 
Forum Jump

Contact Us Archive Advertising Cookie Policy Privacy Statement Terms of Service

We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.