Finally. An exhaust video. SC300
#1
Finally. An exhaust video. SC300
I finally have clips of my exhaust. They should be decent enough for you guys so hopefully it will be enjoyed(no techno music). Please keep negative comments or snide remarks in your head! Did the best with what I had. Film car was a Dodge Charger incase anyone wonders.
http://www.youtube.com/watch?v=4LNTs...ature=youtu.be
http://www.youtube.com/watch?v=4LNTs...ature=youtu.be
#2
Driver
iTrader: (2)
Join Date: Jan 2013
Location: Texas
Posts: 159
Likes: 0
Received 0 Likes
on
0 Posts
Nice sounding car, i have been on the fence about staying dual, or going single.
My exhaust is retarded, i have a header, no cats, both the factory resonators, and no mufflers, just exhaust tips welded were they used to be. It sounds good above 2500rpm, but have horrible rasp below that.
My exhaust is retarded, i have a header, no cats, both the factory resonators, and no mufflers, just exhaust tips welded were they used to be. It sounds good above 2500rpm, but have horrible rasp below that.
#6
Replies
Nice sounding car, i have been on the fence about staying dual, or going single.
My exhaust is retarded, i have a header, no cats, both the factory resonators, and no mufflers, just exhaust tips welded were they used to be. It sounds good above 2500rpm, but have horrible rasp below that.
My exhaust is retarded, i have a header, no cats, both the factory resonators, and no mufflers, just exhaust tips welded were they used to be. It sounds good above 2500rpm, but have horrible rasp below that.
Thank you
HAHA! Not sure about that but I suppose I'll take that
The complete specs are MVP header to 2.5 inch straight pipe with 1 high flow resonator in the middle and then the HKS HI flow muffler.
Trending Topics
#8
Driver
iTrader: (2)
Join Date: Jan 2013
Location: Texas
Posts: 159
Likes: 0
Received 0 Likes
on
0 Posts
Thank you! And I'm sure your frankenstein exhaust should sound good lol
Thank you
HAHA! Not sure about that but I suppose I'll take that
The complete specs are MVP header to 2.5 inch straight pipe with 1 high flow resonator in the middle and then the HKS HI flow muffler.
Thank you
HAHA! Not sure about that but I suppose I'll take that
The complete specs are MVP header to 2.5 inch straight pipe with 1 high flow resonator in the middle and then the HKS HI flow muffler.
#9
I just measured it and its 4 and 3/4 inches. So around 120mm. Now that I know there is a bigger cannon out there I might start to save.
edit: Just did some research, the TIP is 120mm and the actual muffler (or shell) is the big 170mm So I guess you can say I have the larger of the 2.
edit: Just did some research, the TIP is 120mm and the actual muffler (or shell) is the big 170mm So I guess you can say I have the larger of the 2.
Last edited by ashtray; 02-13-13 at 08:05 PM.
#10
Driver
iTrader: (2)
Join Date: Jan 2013
Location: Texas
Posts: 159
Likes: 0
Received 0 Likes
on
0 Posts
http://www.ebay.com/itm/HKS-HI-POWER...-/250844804404
#12
This is the one i am getting, plus i plan on using this new exhaust after i finish the turbo build.
http://www.ebay.com/itm/HKS-HI-POWER...-/250844804404
http://www.ebay.com/itm/HKS-HI-POWER...-/250844804404
Thanks man. Gotta love rev matching downshifts. They sound a ton better live. Thanks again though!
Thread
Thread Starter
Forum
Replies
Last Post